Machine Elements. Please creful with numbers. A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of1- in. The shaft rotates at 613 rev/min and transmits 53 hp through a gear.16Select an appropriate key for the gear.(a) Take a in square key, UNS G10200 cold-drawn steel being used. The design will be based ona yield strength of 65 kpsi. A factor of safety of 2.80 will be employed in the absence of exactinformation about the nature of the load.(b) The same conditions in option (a) but the design will be based on a shear strength of 37.5 kpsiUse Customary units.

Power is given by P = Torque * speed in rpm P = T*n /63025 And , T = F*(D/2) According to…

Answered: A UNS G10350 steel shaft, heat-treated…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide a demonstrated drawing of the figure (construct) as well
Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D= 5.9 inches. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 7 -1.00000 * How deep should she mill the 90° grooves so that the top of the sine block is 2 inches tall? (Round the final answer to four decimal places.) The depth of the mill should be 7071.067 inches.
Question 3 The Extrude Cut feature in SOLIDWORKS can be used to create both through holes (holes that go all the way through a part) and counter bore holes (holes that do not go all the way through a part), such as the holes shown in the 2-dimensional image below. True False Counterbore
Please help. I need help with all 4 questions. Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary basic dimensions. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
Select the correct statement regarding the solid model shown below. pattern1 It is easiest to create the 18 holes in this model by sketching each individual hole and using the extruded boss/base feature. It is easiest to create the 18 holes in this model by sketching one individual hole
Please solve it complete please don't copy paste

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS