A unit step current of 1 A is applied to a network whose driving point impedance is : V(s) (s+4) Z(s) : 3 I(s) (s+2)° The steady state and initial values of the voltage developed across the current source would be respectively Select one: a. -0.375 V, 0 V O b. 0.375 V, 1 V O c. 0.75 V, 0 V O d. OV, -0.375 V e. 1.5 V, 1 V O f. 1 V, 0 V g. 2 V, 1 V "indows buU Rcbi 0.375 V, 1 V O i. 0.5 V, O V

A unit step current of 1 A is applied to a network whose driving point impedance is : V(s) (s+4) Z(s) : 3 I(s) (s+2)° The steady state and initial values of the voltage developed across the current source would be respectively Select one: a. -0.375 V, 0 V O b. 0.375 V, 1 V O c. 0.75 V, 0 V O d. OV, -0.375 V e. 1.5 V, 1 V O f. 1 V, 0 V g. 2 V, 1 V "indows buU Rcbi 0.375 V, 1 V O i. 0.5 V, O V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the circuit in fogure below. Analyze the total current, the current through R5, amd the voltage across R9 amd R10
Find the mesh currents I, and 12. The coupling, k, is equal to 0.5. You need not calculate the actual currents. It's enough to set up the mesh equations. You must redraw the circuit to show the dependent voltage sources. The linear frequency is 3/(2a). V1 22Vpk 3/(2pl) 45* R1 150 Lt 12mH L2 3mH . R2 300
A voltage source is supplying a load through a long cable. The load is consuming 250 VA at 0.82 lagging power factor, and the voltage across it is 180 Vrms. The impedance of the cable is 5 + j4 9. a. The load may be modeled as an impedance consisting of a resistor in series with Choose one: a capacitor / an inductor. b. Draw the circuit that you can use to analyze the problem. Label all circuit elements and variables. c. Using the voltage across the load as the reference phasor, solve for the phasor current around the loop. d. What is the voltage (in rms) across the source? e. What is the real power delivered by the source?
Find the steady state value of the I and the V1 and V2.
A given circuit has a resistor (R=20 ohms) and an inductor (L=0.3 henrys) connected in series with a sinusoidal voltage with the following equation: v(t) = 120v2cos (120t + 10°) a.) Find the current immediately after switching b.) Find the magnitude of impedance (in ohms) c.) Find the steady-state RMS current in amperes
#11 please choose the correct answer, show your complete solution
Q5) In the circuit shown in Figure, find: 1) R 2) last. I E-24V
Q2. For the circuit shown in Figure Q2, determine the following at steady-state condition: R₂ www. IN (a) The currents 11 and 12 in the inductors, (b) The voltages V1 and V2 across the capacitors (c) The total energy stored in the circuit (d) The charge in the capacitor C2 E SOV 2552 42 45 8570
answer the following question
Consider the following circuit used to provide power for an inductive RL load. The input voltage is Vs=150V and the load has a 30 impedance value. The thyristor is working at a frequency fs = 2 kHz. The discharge current is to be limited to 50A and the required dv/dt is 50V/us. The values of Rs and Cs are equal to: Cs Ti V, Select one: O a. 30, 0.158µF b. 30, 0.352µF ос. 30, 0.64µF O d. 60, 0.5µF
Differential Equation Applications An electromotive force of 100 volts is applied to an RC series circuit, in which the resistance is 200 ohms and the capacitance is de10-4 farads. Determine the load q(t) of the capacitor, if q(0) = 0. Find the current i(t)
A 1000-VA, 230/115-V transformer has been tested to determine its equivalent cir- cuit. The results of the tests are shown below. Open-circuit test (on secondary side) Short-circuit test (on primary side) Voc = 115 V Vsc = 17.1 V %3D %3D Isc 8.7 A Psc loc =0.11 A Poc = 3.9 W = 38.1 W (a) Find the equivalent circuit of this transformer referred to the low-voltage side of the transformer. (b) Find the transformer's voltage regulation at rated conditions and (1) 0.8 PF lag- ging, (2) 1.0 PF, (3) 0.8 PF leading. (c) Determine the transformer's efficiency at rated conditions and 0.8 PF lagging.