A uniform wire of length I= 800 m and cross-sectional area S= 1.0 mm² is made of a material of densityp=8.0 x 103 kg/m³ and Young's modulus Y= 2.0 × 1011 N/m2. The wire is placed straight on a frictionless hori- zontal floor and an end is pulled by a constant horizontal force F = 1.0 N'uniformly distributed over the face of the end. Find displacement of this end in a time interval At = 0.1 s after the force is applied. %3D

Q: 38 17 Hole Tam delik 18 19 20 20 8 26, 20. 89

A: Given:-

Q: What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing…

A: According to the given data Horizontal distance between A and B =18 Vertical Distance between A and…

Q: ab) What is the composite area's moment of inertia based on axis Yo?

A: we have to determine the MOI

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: The isometric view is given in the above figure.We have to find out multiview of the given isometric…

Q: Using the graphical method, find the sum of the vectors in each number. Draw your vectors on a…

A: The given data in the problem is listed in the following attached image:

Q: Could you solve the last 3 options (c, d, e) please

A:

Q: For #16.6 on page 669, do the followings: 1) Draw the top, the front, and the right-side…

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: Show from the following data taken for the automobile test performed on a 4 cylinder gasoline engine…

A:

Q: F= 200 N %3D 30° 13 12 F2 = 260 N

A:

Q: Match the letter to the correct part description based on the picture of the milling machine below.

A: Milling Machine Parts name

Q: 1. drawing provides information about size and tolerances for the manufacture of the parts. 2. The…

A: Given Drawing To find Fill in the blanks

Q: Need help please all 3 go together

A:

Q: For the given isometric drawing, draw the corresponding top, front, and right side view. L HRP FRP L…

A: For the given isometric drawing, draw the corresponding top, front, and right side view.

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: 1. How is fraction changed to decimal? A. Divide the denominator by the numerator B. Divide the…

A: Since we answer only one question at a time, we will answer the first one. Please resubmit the…

Q: Use basic drawing instruments (pencil, scale, protractor, compass, etc). A hexagonal prism with side…

A: In the below figure, we can see on the right-hand side the development of sectioned hexagonal prism.…

Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the num true stress…

A: Given lo =50mm l=60 mm K= 210 MPa n=0.27

Q: Find the value of P

A: Need to find Values of P

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: F 400 N E-600 N 45 30

A: Given: F1 = 600 N F2 = 400 N   To find: FR = ? and direction of resultant using parallelogram law of…

Q: 2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: ## Determining the Net Torque on the Wheel (Considering the Image)The image  shows a wheel with…

Q: What is the difference between corrective maintenance and preventive maintenance ?

A: After equipment fails, corrective maintenance (CM) entails its replacement or repair. When…

Q: What is the distance between the points labeled A and B? Start a new drawing based on…

A: According to the given data Thickness of the wall=100mm We need to find Distance b/w A and B

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Complete the each drawing by adding the missing details in 5 and 6 both questions.

A:

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: TOP FRONT SIDE

A: GIVEN DATA ISOMETRIC VIEW GIVEN WE HAVE TO DRAW ORTHOGRAPHIC VIEWS OF GIVEN FIGURE

Q: Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless…

A:

Q: Draw the Isometric drawing of the given orthographic projections below. Use drawing scale to fit the…

A:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Note: As per the policy, we can solve the first question from the multiple question. Please,…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: 4. Specific Weight is also called Relative Density. 5. Standard density of water in English unit is…

A: It is required to determine whether the following statements are correct or not: 4. Specific weight…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.