Answered: A uniform hoop of mass m and radius r… | bartleby

Related questions

Question

A uniform hoop of mass m and radius r rolls without slipping on a fixed
cylinder of radius R. The only external force is that of gravity. If the smaller
cylinder starts rolling from rest on top of the bigger cylinder, use the method
of Lagrange multipliers to find the point at which the hoop falls off the
cylinder.

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A uniform solid disk of mass M and radius R hangs from a string of length ℓ attached to a smooth vertical wall (see the figure attached). Calculate the tension in the string and the normal force acting at the point of contact of disk and wall.
A solid sphere, a spherical shell, a hoop, and a disk all with mass M and radius R roll without slipping with the same speed along a flat surface. They then start to roll up a slope that makes and angle θ with respect to the horizontal. Which object gets the farthest up the slope before rolling back down?
Refer to the question below.
A uniform sphere of mass m and radius R rolls without slipping down a plane at an angle θ from thehorizontal. Show that the acceleration along the slope of the center of mass is aCM = (5/7)g sin θ and that the force of static friction needed is fs = (2/7)mg sin θ. What minimum coefcient of friction µs is needed to satisfythe conditions of the problem?
A bicycle wheel is spinning at a constantspeed. You note that a piece of tape on theedge of the wheel completes 25 fullrotations in 19 seconds. What is the angularfrequency of the bicycle wheel?
In the figure below, the disk, of mass 440 g and radius 3.5 cm, is rotating at 180 rpm on a frictionless shaft of negligible radius. The upper disk, of mass 270 g and radius 2.3 cm, is initially not rotating. It drops freely down onto the lower dis, and frictional forces bring the two disk to a common rotational speed. Find (a) that common speed and (b) the fraction of the initial kinetic energy lost to friction.
The uniform thin rod in the figure below has mass M = 2.00 kg and length L = 3.25 m and is free to rotate on a frictionless pin. At the instant the rod is released from rest in the horizontal position, find the magnitude of the rod's angular acceleration, the tangential acceleration of the rod's center of mass, and the tangential acceleration of the rod's free end.
A uniform, solid sphere of radius 6.00 cm and mass 4.50 kg starts with a purely translational speed of 2.50 m/s at the top of an inclined plane. The surface of the incline is 2.00 m long, and is tilted at an angle of 32.0∘ with respect to the horizontal. Assuming the sphere rolls without slipping down the incline, calculate the sphere's final translational speed v2 at the bottom of the ramp. v2= m/s
A frisbee’s stability is maintained by its angular momentum. A 175gram frisbee with a diameter of 12inchesis thrown with an angular velocity of 5rev/s . Assume the frisbee can be modeled as a flat solid disk. Find the magnitude of the angular momentum vector.
Asmall cube (M = 0.45 kg) is at a height of 315 cm up a frictionless track which has a loop of radius, R= 47.25 cm at the bottom. The %3D cube slides freely down the ramp and around the loop. Find the velocity of the block when it is at the top of the loop. V H R
The string is massless. The pulley turns on frictionless bearings. Consider the pulley as a uniform disk of mass 2.50 kg and radius 5.00 cm.T he mass m1= 4.00 kg, and the mass m2= 5.00 kg. The system is released from rest. Find (a) the acceleration of m1, and (b) the tensions, T1& T2,in the horizontal and vertical portions of the string. The horizontal surface below m1is smooth.
The 6kg multiple pulley disc is configured as shown for an experiment. The disk is unbalanced with a radius of gyration KG = 50 cm about its mass center G and experiences a resisting torque of 0.3 N - m at pin C. Block A with mass = (0.623) kg hangs off a rope wrapped around the 250 mm pulley on the right side. If the system is released from rest, (a) What is the angular acceleration of the disk in rad/s²? (b) Find the tension in the rope in Newtons (c) You are tasked with doubling the acceleration solved in (a) by hanging another block off the 150 mm pulley. Determine the mass of the block in kg necessary to achieve this. Indicate which side of the 150 mm pulley you should hang the second block from. NOTE: draw the FBD and the KD 8cm- 150mm 250mm Block A