A U-tube contains a liquid of relative density 1.25 to a height of 25 cm in both the columns. It is rotated about a symmetrical vertical axis with 15 cm from both the limbs. Calculate the pressure at the bottom end points and mid point when the speed of rotation is 240 revolution per minute. 15cm--15cm- 25 cm IM

A U-tube contains a liquid of relative density 1.25 to a height of 25 cm in both the columns. It is rotated about a symmetrical vertical axis with 15 cm from both the limbs. Calculate the pressure at the bottom end points and mid point when the speed of rotation is 240 revolution per minute. 15cm--15cm- 25 cm IM

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 1-m-diameter cylindrical mass, M, is connected to a 2-m wide rectangular gate as shown in the…

Q: Calculate the surface tension of the fluid (SG = 8.6) in the capillary tube below: Зтт h = 2mm e =…

Q: 3 t/m 10 t 8 tm H. 4 m 3 m 6 m

Q: Two identical spheres weighing 100 KN each are placed in a container such that the lower sphere will…

Q: COMPUTE THE CAPILLARY RISE IN mm. OF PURE WATER AT 10^0 C EXPECTED IN A 0.8 mm θ TUBE

Q: The tank below is open to the atmosphere. A hinged door located 10 m below the top of the tank.…

Q: Three smooth identical cylinders A, B and C stacked in a V-shaped trough as shown (weight 400 N and…

Q: diameter = 60 cm height = 60 cm The open cylindrical tank is two-thirds full of water.…

A: H=0.4m R=60/2 R=30cm

Q: a.) Determine the pressure difference between the two vessels when the difference in the levels of…

Q: 180 kg M

Q: The ball B of negligible size rolls through the tube such that at the instant shown in (Figure 1) it…

A: Given: To find: Part A: Velocity of the ball if the tube has an angular velocity, ω = 3 rads/s and…

Q: Calculate the hydrostatic force and components of the semicylindrical protuberance located at the…

A: The objective of the question is to calculate the hydrostatic force exerted on a semicylindrical…

Q: 4. A1.2-meter-diameter cylinder, 1.2-meter-long is acted upon by water at 4 °C and oil (sg = 0.8) as…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

A U-tube contains a liquid of relative density 1.25 to a height of 25 cm in both the
columns. It is rotated about a symmetrical vertical axis with 15 cm from both the
limbs. Calculate the pressure at the bottom end points and mid point when the speed
of rotation is 240 revolution per minute.
15cm--15cm-
25 cm
IM
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown. Compute the vertical reaction at B
The 2kg collar is released from rest at A and slides down the inclined fixed rod in the vertical plane. The coefficient of kinetic friction is 0.40. Calculate the a. Velocity of the collarwhen the spring has been compressed 40mm b. Velocity of collar before it hits the spring
Compute the value of F1, F2, and F3 in Newtons
A rectangular open tank is 6m long, 2m deep and 2m wide is containing water up to 1m height. If the tank is subjected to horizontal acceleration of 3 m/s2, find (i) angle of water deformation on the surface (θ) (ii) force on each end during acceleration (γ = 9790 N/m3)
The 8 ft diameter cylinder weighs 500 lb and rest on the bottom of the tank that is 3ft long, water and oil are poured into the left and right portions of the tank to depths of 2ft and 4ft respectively. Find the net horizontal hydrostatic force and the Reaction at B water 2 ft FH(water) = 374.4 lb FH(oil) = 1123.2 lb RB = 2184.12 lb r=4ft 4 ft oil 0.75
A cylindrical drum of length l and radius r can rotate inside a fixed concentric cylindrical casing, the clearance space c between the drum and the casing being very small and filled with liquid of dynamic viscosity µ. To rotate the drum with angular velocity o requires the same power as to pump the liquid axially through the clearance space while the drum is stationary, and the pressure difference between the ends of the drum is p. The motion in both cases is laminar. Neglecting end effects, show that 2µlro/3 p = c2
Q2. A cylindricai tank of diameter 2.5 m is founded with its axis horizontal. The tank contains water in the bottom half and an oil of relative density 0.82 on the top haif with a common interface. The fluids are under pressure and a pressure gauge on the top of the cylinder reads 15 KPa. Caleulate the force per meter length on the upper half of the cylindrical tank.
The angular velocity wac = 5.6° per second. Determine the angular velocity of the hydraulic actuator BC in deg/s. L = 1.38 m 2L2 = 1.15 m 2L2 - Li --- L2 -
Heavy fuel oil flows at Q = 10 gallons per minute (gpm) in a horizontal steel pipe that connects two storage tanks. The diameter of the pipe is D = 1.5 inches. The length of the pipe is L = 100 feet. The depth of oil in the supply tank is 30 feet above the pipe entrance. The temperature of the oil is 60°F, the specific gravity of the oil is s.g.oin = 0.90, the specific weight of the oil is 56.13 lb/ft', and the kinematic viscosity of the oil is 0.00175 ft2/s. The pipe discharges into the bottom of the receiving tank. Neglect minor losses. a) Determine the pressure p at the pipe entrance in pounds per square foot (psf). b) Determine the velocity v in feet per second (fps). c) Determine the Reynolds number Re. d) Classify the flow based on the Reynolds number Re. e) Determine the Darcy-Weisbach friction factor f. f) Determine the friction head loss hfac in feet in the pipe between the two storage tanks. 8) Determine the depth of oil in feet above the exit from the pipe into the second…
The radii of the press plunger and the pump plunger are in the ratio 30:4. If an effort of 32kgf acts on the pump plunger. Find the maximum effort the press plunger can overcome. (in kgf)
Ex. A pitot static probe is inserted into duct of air heating system parall to flow and the differential height of the water Colum is measured. The flow velocity and the pressure rise at the of the pitot -statics probe are to be determined For water p = 1000 kg/m3. for air p = 1.1 kg/m3 Air h-2.4 cm
Question Certain fluid parameters are provided The inner cylinder, with a diameter of 20 cm, remains stationary, while the outer cylinder, with a diameter of 21 cm, holds the liquid up to a height of 30 cm. There is a 1.0 cm gap between the bottom of the two cylinders. By rotating the outer cylinder at a speed of 200 revolutions per minute (r.p.m.), the torsion meter attached to the inner cylinder registers a torque of 6.0 N-m. a. Determine the toque on the bottom in terms of b. Determine the toque on the surface in terms of ..... c. Determine method the viscosity of a liquid (N-sec/m^2)(Ans up to 2 decimal) μ (Ans up to 4 decimal) ..u.(Ans up to 4 decimal) using the rotating cylinder