A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10-8 m³ / s. What is the viscosity of the fluid?

A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10-8 m³ / s. What is the viscosity of the fluid?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure drop in a Venturi meter varies only with the fluid density, pipe approach velocity, and the diameter ratio of the meter. A model Venturi meter tested in water at 20 ?C shows a 5-kPa drop when the approach velocity is 4 m/s. A geometrically similar prototype meter is used to measure 680 kg/m3) at 20 ?C and a flow rate of 9 m3/min. If the prototype pressure gage is most accurate at 15-kPa, what should the upstream pipe diameter be? gasoline (? =
2. A large-capacity faucet is to be connected to a water main by 20-mm diameter copper tubing as shown in Figure below. The copper tubing has an estimated f=0.02, and local head losses are created by the corporation stop (C-stop), three bends, and the faucet itself. The faucet exit has a diameter of 12 mm. What is minimum pressure in the water main required to obtain a desired flow rate of 50 L/min when the faucet is fully open? fig1.Faucet connected to water main. Water main Bend 3.5 m C-stop E 2 5m Pipe Bend Bend E Bend 4 m Faucet Fitting C-stop Bend(s) Faucet K 9 1.2 10
Answered quickly explanation
Problem 3. Honey is being pumped through a network of small tubes with inner diamter D = 15 um (Fig. 1). The straight section of the tube has length of L = 5 cm, while the circular section of the tube forms a circle with radius R = 5 cm. 1. Given the viscosity of honey µhoney and assuming the flow splits evenly at the intersections, what is the total pressure drop required to maintain a flow rate Q = 0.5 mL/min as predicted by Poiseuille's law? = 10 Pa-s, density of honey Phoney = 1450 kg/m³, 2. Does the Reynolds number of the flow support the use of Poiseuille's law? R L L Figure 2: Honey is being pumped through a network of small tubes.
E10
a.)In the figure shown in no.1, in which fluid will a gage pressure of 60 kPa first be achieved? b.)In the figure, in which fluid will a gage pressure of 80 kPa first be achieved?*
A closed tank is filled with oil and water with the given situation as shown in the figure. An orifice with an unknown diameter is placed 1 m from the bottom of the tank discharging 10 L/s based on a calibration test. The jet from the orifice hits the ground 3.8 m horizontally away from the vena contracta. If the coefficient of discharge is 0.64, determine: a. The diameter of the orifice b. The coefficient of cotraction. Air p- 16 KPa 1 m S0.82 3.80 m Water 1m 2 m 1m
A sample of gas occupies 3.75 L at 1.15 atm and 25 °C. At what temperature will it occupy 4.00 L at 1.00 atm? Initial: Final: Effect:
An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]
Read the question carefully and give me right solution according to the question.
Three liquids given the following properties are poured into the cylindrical container with a diameter of 3 meters and a height of 6 meters. First fluid poured: sg = 1.0 , V = 17.6715 m^3 Second fluid poured: sg = 0.81 , V = 10.6029 m^3 Third fluid poured: sg = 2.94 , V = 7.0686 m^3 Assuming that the container is closed after pouring the fluids and the stable state in the container is reached, determine the pressure at the height of 4-m from the bottom of the tank
An oil with p= 900 kg/m and v= in Fig. E6.4. The pressure and elevation are known at sections 1 and 2, 10 m apart. Assuming 0.0002 m'/s flows upward through an inclined pipe as shown d=6 cm 10 m Pz= 250,000 Pa 40 P 350,000 Pa, z =0 steady laminar flow, (a) vetify that the flow is up, (b) compute h, between I and 2, and compute (c) Q. (d) V, and (e) Re. Is the flow really laminar? pgd'h 128uL 2,431, Eu 66 70 & Density of Air p = 1.205 kg/m 364 S44 o176 = 15 11 o76 +rso k Coefficient of viscosity for air u = 1.80 x 10-5 K hy = 151 355m Force of gravity = 9.807 Density of water p= 998 kg/m3 Coefficient of viscosity (water) u = 0.001 kg/(m.s) For gasoline at 20°C, from the Table p= 680 kg/m'y = pg, g =9.81