A typical 1-in. chlorine gas is carried by using Schedule 40 horizontal steel pipe. At a pressure of 6 atm abs, a temperature of 120 °C, and a velocity of 35 m/s, the gas enters the pipe through a rounded opening. Considering that such a flow happens isothermally. (c) What then is the pipe's maximum length? (d) When the length equals the maximum, how much heat must be delivered to the gas?

A typical 1-in. chlorine gas is carried by using Schedule 40 horizontal steel pipe. At a pressure of 6 atm abs, a temperature of 120 °C, and a velocity of 35 m/s, the gas enters the pipe through a rounded opening. Considering that such a flow happens isothermally. (c) What then is the pipe's maximum length? (d) When the length equals the maximum, how much heat must be delivered to the gas?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Plz correct solution.
QUESTION 6 A cylindrical tank, containing water, with a diameter of 3 m and a water level of 5 m is to be drained. Calculate the time taken in minutes to empty the tank for the following cases: 6.1 Two orifices fitted in the bottom with a diameter of 50 mm and coefficient of discharge CD = 0.785 6.2 A pipe with internal diameter, length, coefficient of friction, of 50 mm, 6 m, 0.008, respectively, and the outlet 2 m below the bottom. 6.3 A pipe with internal diameter, length, of 50 mm and 6 m respectively, an outlet 4 m below the bottom, and a valve with a loss factor of 2.8.
a) Calculate the maximum flux the liquid water can have ( η = 0.891 cP and ρ = 0.998 g/mL a 20 ºC) when flowing through a 2 mm diameter tube, in the laminar regime.b) If the pressure when entering the tube is 1 bar, how many meters will it need for the pressure to decrease a 10%? Data: dina/cm3 = 10 Pa/m; 1 bar = 105 Pa. Results: 2.81 cm3/s, 1.57 m
sg(water@25degree)=9.78kN/m^3 k=0.42
Question 12 A circular pipe has a 4.6 in diameter opening and a 2.5 in diameter throat. MSL air enters the pipe at 13.0 mph. What is the pressure of the air in the throat (tenths)? Your Answer: Answer units
Investigate the mass flow rate of oil inside the Alaskan pipeline, and write a brief report to your instructor discussing your findings.
Wasit University / College of Engineering Section 10: Pipe Design 10.8 Example Determine the pressure or head losses for a 25 mm threaded steel pipe tee flowing 25% to the side branch, 75% through. The entering flow is 1 L/s at velocity of 1.79 m/s.
10. Water at a temperature of 800C (coefficient of viscosity is 0.357 centipoise) is flowing at a speed of 200 cm/s through a pipe of radius 2 mm. What is the nature of flow? What is the maximum velocity for it to remain laminar? What is the minimum velocity that will make the flow turbulent?
12. Points A and B are 3000 ft apart along a 10-in. new steel pipe. B is 220 ft higher than A. With a flow of 3.2 efs of water from A to B, what pressure must be maintained at A if the pressure at B is to be 50 Ib per sq in.? Answer should be: 164 lb per sq. inch Show your handwritten solution.
The static head at a certain station on a 101.6 mm schedule 40, clean iron cold pipe is 70.69 m The static head is to be determined for a station 162.4 m farther along the pipe in the direction of flow,and where the pipe is 10.14 m higher than station 1. Between the stations are two elbows. Flow rateis 1452 l/min.
1.A 0.5 m pipe is flowing with water at temperatures of 30 ^o C and 40 ^o C. Calculate the maximum velocity under conditions A.Laminar B.Turbulent