A two storey building has two faucets, one in the basement and one in the first floor. The maximum water (p= 1000 kg/m³) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm. Neglect all losses. (a) How much is the maximum velocity at the first floor faucet, when the basement faucet is closed?

A two storey building has two faucets, one in the basement and one in the first floor. The maximum water (p= 1000 kg/m³) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm. Neglect all losses. (a) How much is the maximum velocity at the first floor faucet, when the basement faucet is closed?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

.
Q1 The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated with this machine? If the flow discharge is 200 lps, PA = 206 kN/m, Pg = 690 kN/m, elevation of A = 67 m and elevation of B= 30 m. Neglect losses. D- 300 mm D-200 mm Fig (3)
In the Figure.Q3, The energy decline of the connections and the pipe before the pump is 3m. (Patm=105 Pa and Py=4X104 Pa) 4 m 7 m PUMP Fig.Q3 i. Calculate the available net positive suction head (NPSH).
The calculation of power from moving fluid has the following parameters:Volume flow rate = 10 +/- 0.154 m3/sDensity of Water = 1025 kg/m3Head of water = 150m +/- 10cmDetermine the range of values the power will be calculated.
Use Bernoulli's Theorem
At the end of the summer, a swimming pool is being drained through a very long,small-diameter hose. The hose is smooth, of inner diameter D = 6.0 cm,and of length L = 65 m. The initial height difference from the pool surface to theoutlet of the hose is H = 2.20 m. Calculate the volume flow rate in litres per minute(LPM) at the start of draining.
In the Venturi of the kerosene figure (density: = 0.85 ) seeps as ideal fluid. The area in section (1) is 24 cm2 while that of section (2) is 12 cm2. The average kerosene velocities in sections (1) and (2) are 4.5 m/s and 9 m/s, respectively. A manometer whose manometric fluid is mercury (y=133280 N/m3) is connected between sections (1) and (2) and indicates an unevenness "h". Find the unevenness ''h'' answer:0,206m
Oil (density = 842 kg/m³ and kinematic viscosity = 6.2e - 4 m²/s) is being discharged by a 66 mm diameter, 3 m long horizontal pipe from a storage tank open to atmosphere. The height of the liquid above the centre of pipe is 1 m. Disregarding the minor losses, determine (to 4 decimal places): a) the volumetric flow rate of the oil through the pipe m³/s b) the corresponding Re number.
Examples & The Inlet to pump is 10.50m above the bottom of sump from which it draw water through a suction pipe. If the pressure at the pamp inlet is not to fall bellow 28 kN/m² absolute, work out the minimum depth of water in the tank 6.019 m O 15m 0 3.019 m O 9.019 m O 1.019 m O
O.S. A vertical orifice is 10 cm. square and has an actual flow of 28 Ips with Cv=0.95, Cv = 0.62 as shown in the figure. If the liquid is oil (s.g. = 0.85), what is the head, h in meter over the orifice is required? determine the theoretical velocity of the jet determine the theoretical flow (Ips).
Here, a flow rate of 2 m3/s is active in a pipe, as seen in the attached figure. What is the expected power output of the turbine with 70% efficiency if the elevation difference of the reservoir surfaces is 60 m? How would I draw a EGL and HGL for this system?
Three pipes A,B and C connected in seies discharges 160 L/s of water. The properties of pipe: for pipe A,L= 1800 m, diameter= 0.90 m f= 0.012; for pipe B, L= 1500 m, diameter= 0.60 m f=0.012 and for pipe C, L= 800 m , diameter = 0/45 m, f= 0.012. Disregarding minor losses, find the total head loss of the pipe. Include the diagram in your solution. a.0.078 m. b.1.15 m. c.0.492 m. d.1.675 m.