A truck with axle loads of 30 kN and 60 kN on a wheel base of 4 m rolls across a 10-m span. Compute the maximum bending moment in kN-m.

A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?

A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?

A tall cylindrical silo carrying flour is to be supported by a 1.5 m wide ring beam that can be designed as a continuous foundation. The inner and outer diameters of the ring are 10 m and 13 m, respectively. The soil at the site is entirely sand (ф′ = 35°, γ = 19 kN/m3) and the ring beam is placed on the ground with Df = 0. Determine the maximum silo load that can be carried by the ring beam, assuming that the entire load is transferred to the ground through the ring beam.

In a piled raft, 450 mm diameter and 13 m long piles are placed in a rectangular grid at 1.60 m 1.63 m spacing. Find the pile-raft interaction factor assuming uniform soil conditions with depth and

The tie rods from anchored sheet piles will be connected using a row of anchors, as shown in Figure 18.46a. Here H = 2.0 m, h = 1.25 m, B = 1.5 m, S = 2.5 m, = 32, and = 17.5 kN/m3. The anchor plates are made of 100 mm thick reinforced concrete with a unit weight of 24.0 kN/m3. Determine the ultimate holding capacity of the anchor used Ovesen and Stromanns method.

A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone: Unconfined compression strength = qu(lab) = 78.7 MN/m2 Angle of friction = 36 Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).

A braced cut shown in Figure P19.3 is to be made to a depth of 9.0 m in a saturated clay deposit where the unit weight is 17.65 kN/m3 and the undrained shear strength is 30 kN/m2. The struts are spaced horizontally at 3.0 m center to center. Find the strut loads.

Determine the maximum column load that can be applied on a 1.5 m 1.5 m square foundation, placed at a depth of 1.0 m within a soil, where = 19.0 kN/m3, c = 10 kN/m2 and =24. Allow a factor of safety of 3.0.

Determine the factor of safety against bottom heave for the braced cut described in Problem 15.18. Use Eqs. (15.66) and (15.70). For Eq. (15.70), assume the length of the cut, L = 18 m. 15.18 Refer to Figure 15.51 in which = 17.5 kN/m3, c = 60 kN/m2, and center-to-center spacing of struts is 5 m. Draw the earth pressure envelope and determine the strut loads at levels A, B, and C. FIG. 15.51