A triangular distributed load of max intensity w acts on beam AB. The beam is supported by a pin at A and member CD, which is connected by pins at C and D respectively. Determine the largest load intensity, wmax, that can be applied if the pin at D can support a maximum force of Dmax - 20000 N. Also determine the reactions at A and C and express each answer in Cartesian components. Assume the masses of both beam AB and member CD are negligible. a b A С C cc 130 BY NC SA 2016 Eric Davishahl D The maximum load intensity is wmax= → The reaction at A is A = 0 The reaction at C is C = 0 Y₁ Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 6.9 m 13.11 m 4.83 m xi + 67000 x + 20000 x N/m. W' xjN. xjN. B

Q: 2. Sharp notches are often added to plastic food packages to help open them (along with arrows…

A: Detailed explanation:Sharp notches are a very good example of the functional features to the plastic…

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Let's work through the calculations for the given L-shaped object.### Part a: Finding the x-centroid…

Q: 10 1 R6 1 10 20 50 30 R10 -5 X 45.00° 50 1 1 5 15 5 R30 110 R5 55 20 R6 7 8 60 30 -60 店 06-4 holes…

A: Step 1: First create following top view and extrude it up to required depth i.e. 60 mm

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: Name 3 types of fits?

A: The different types of fits are : 1) Clearance fit 2) Interference fit 3) Transition fit

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: Step 1: Given: specific gravity, G=1.7 The objective is to determine: a. density of fluid in…

A: Specific gravity G = 1.7Find(1) Density ρ(2) specific weight ɣ

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: Note 1 indicates 10 GAGE 1010-1020 sheet metal can be used to make the main body of this part…

A: Tolerance is the difference between the maximum size and the minimum size of the part or element.

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: Question 4 )Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Radiation

Radiation can be described as the energy in the form of a particular matter or electromagnetic waves traveling in the air and can be in the form of light, sound, and heat. Radiation can be detected through special instruments like X-rays. The radiation from a cooler object is less intense as compared to the radiation from hot objects.