A traveling wave propagating down a long string has an equation of motion given by y(x,t) = 6 sin [7 (3x − 3.8t)] [mm] Calculate a) angular frequency b) wave constant c) wave speed d) Amplitude

Q: Impact velocity equation

A:

Q: isc SC

A: given:discuss how the cylindercal square is used?

Q: Percentage of carbon of medium carbon steel,high carbon steel,lower carbon steel.

A: Application: Used in railway wheels and tracks ,gears ,crankshaft etc

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: Is  this statment correct  Thick pearlite is not as strong as thin pearlite.

A: True , Thick(Coarse) pearlite do have less strength and hardness in comparison to thin(fine)…

Q: 2. Given: ON = 40 % and op = 9 % in a thick clean (no sand) shale ON = 32 % and op = 20 % for zone A…

A: Using Neutron-Density crossplot : Zone A Shale volume,

Q: Do the auxiliary view of this drawing

A: According to the details provided in the question, we need to calculate the auxiliary view. the…

Q: You do not need to provide Given, Assume, and Problem Type/Features for this  question. You just…

A: DefinitionStatic Equilibrium:If a body is at rest and experiences zero force or zero torque, this is…

Q: 9. What is the CNA? (I don't know what it means, but something related to engineering, what would…

A: There are many acronyms for CNA . But as you mentioned it is related to engineering field it stands…

Q: Need auxiliary views of this drawing

A: This question is based on the concept of engineering drawing.

Q: Instruction: : Explain briefly the hardening pr0cess Of a metal.

A: given; explain briefly the hardening process of a metal.

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First 3. angle…

A: First draw the given front view and side view of casting.

Q: What is areal velocity?

A: The measure of the velocity of one celestial body in orbit to another body which is equal to the…

Q: The hand writing is not very clear :(

A: Basically the miller indices are the set of numbers which define the particular plane in the crystal…

Q: A tray with 40 cm diameter contains xylene CgH10. Assume combustion efficiency, X=0.75 a) Calculate…

A: COMBUSTION EFFICIENCY As others have remarked, burning effectiveness has generally been determined…

Q: Gas welding and picture and hand drawing . !

A:

Q: List 10 materials of a windmill.

A: Wind mill: It is mechanical device which convert the kinetic energy of the air into the mechanical…

Q: 32 - (CLO-1) What is cold shut defect? a) Two portions of metal flow together but there is lack of…

A: Cold shut is a casting defect

Q: Tempering refers to a. the amount of galvinization O b. amount of cold reduction c. amount of hot…

A: Tempering: 1. It is the heat treatment process in which we heat the material to a specific…

Q: Mr.Tariq wants to get material testing for his casting components where he doesn't want to damage…

A:

Q: According to the carbon content, carbon steel can be divided into

A: The basic constituents of the steel is iron and carbon with small amount of some other materials…

Q: The ratio of the solidification time

A: Given; Solidification time of a casting is proportional to      ⇒    VA2where, v=volume A= total…

Q: What is the minimum pressure required to reduce volume of a brass sphere by 0.00003 %?

A: Given:reduction in volume=0.00003%

Q: Why does seawater have lower freezing point that pure water?

A: Pure water freezes at 00 Celsius, but seawater freezes at -1.80 Celsius. This is caused by a…

Q: Please sketch this in solidwork and find the surface area and volume. Take a screen shot and post it…

A: The model needs to be drawn on Solidworks and the surface area and volume has to be calculated

Q: quèstion 15 The primary purpose of a chipping hammer during welding is to O A. Prevent oxidation and…

A:

Q: 39 - (CLO-2) I. Deep drawing II. Extrusion III. Forging IV. Rolling Which one(s) is/are bulk…

A: 39) option b is correct.

Q: -450.76 for parts (c) and (d) are incorrect.

A: To determine:c)The gauge pressure at point 2d)The gauge pressure at point 3

Q: 35 - Which of the following statements about supports is false? A) There is no freedom of movement…

A: Degrees of freedom is the no of the independent variable required to define the movement of a…

Q: 5/. is an example for amorphous structure. a. Glass b. Magnesium c. Iron d. Stainless steel

A: Material structures are basically divided into two categories  1) crystalline structure  2)…

Q: Could you please help me in part e & f. The answer for the other parts are: a) By=20kn & Ay=13kn…

A: The Answer is below

Q: Can you pls slove this question briefly with hand written notes and diagram

A:

Q: 1- What are the Lachrange equations for the particle in the given figure? A) L=mR-0² – mgRcos0 B) L=…

A:

Q: Draw the sectional view of the solid and provide necessary dimensions. E 7 Scale 1:2 Draw the…

A: According to the given datatwo object views are givenWe need to draw the section view of the problem

Q: explaing briefly heating curve of pure iron with a neat sketch

A: A heating curve is a graphical plot of the changes in temperature with time for a material over the…

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: Which of these microstructures arrangements is going from high to low strengths? O a) Martensite,…

A: To find : Rank the microstructures arrangements from high strength to low strength

Q: 7 Select the correct appropriate option for the following:- Assertion(A):- Energy barrier for…

A: This question is related with surface chemistry and material science concepts.

Q: 10- Cast Structure are: Chill Zone, Columnar Zone and equlaxed Zone O True O False

A: The given statement is true.

Q: In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A: In wire drawing, Material is extruded .

Q: A realistic value of Poisson's ratio for steel is... Select one: O a. 70 O b. 0.1% O c. 0.002 O d.…

A:

Q: In sand casting process, the pattern is made of metal wood O plastic all of these

A: