A transmission shaft, supporting two pulleys A and B and mounted between two bearings C, and C, is shown in figure below. Power is transmitted from the pulley A to B. The shaft is made of plain carbon steel 45CS (Sut = 600 and Syt = 380 N/mm?). The pulleys are keyed to the shaft. Detemine the shaft diameter if k, =1.5 and k = 1.0. 500 N 30 300 1500 N 100- -200 150- -2004-

A transmission shaft, supporting two pulleys A and B and mounted between two bearings C, and C, is shown in figure below. Power is transmitted from the pulley A to B. The shaft is made of plain carbon steel 45CS (Sut = 600 and Syt = 380 N/mm?). The pulleys are keyed to the shaft. Detemine the shaft diameter if k, =1.5 and k = 1.0. 500 N 30 300 1500 N 100- -200 150- -2004-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is
Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T1 = T2 = 1000 lb-in. 500 lb-in. A B T3 = 800 Ib-in. C Ta = 500 lb-in. d = 1.0 in. D T; = 800 lb-in. E
A line shaft supporting two pulleys A and B is shown in figure below. Power is supplied to the shaft by means of a vertical belt on the pulley A, which is then transmitted to the pulley B carrying a horizontal belt. The ratio of belt tension on tight and loose sides is 3:1. The limiting value of tension in the belts is 2.7 kN. The shaft is made of plain carbon steel 40C8 (Sut = 650 N/mm2 and Syt = 380 N/mm2). The pulleys are keyed to the shaft. Determine the diameter of the shaft if, k = 1.5 and k, = 1.0. (Sm valing odi of 450 A B 2500 22.0=1821 P3 4500 250 ₁ 4500 P1 A P₂ P4
Problem 1: (P9, P10, M5, M7, D5) Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1=2880 N and T2-432 N. The maximum bending moment is at x =230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). 230 mm 280 mm 30-mm dia. 300 mm 250-mm dia. 400-mm dia. 270 N X. 1800 N
The two solid steel shafts shown in the figure are connected together using gear wheels. The length of the CD shaft is Lcd=2 m and the length of the AB shaft is LAB= 1.5 m. The radius of gear C is rc=45 mm and the radius of gear B is rB= 90 mm. The CD and AB shafts rotate freely in the bearings on which they are supported. Also, shaft AB is fixed at point A. Each shaft has a diameter of 20 mm and a shear modulus of G=65 GPa. When a torque of T= 450 N.m is applied to the CD shaft from the D end;a) Calculate the torsion angle on shaft AB. (Write your result in radians.)b) Calculate the total rotation (torsion angle) of the D end of the CD shaft. (Write your result in radians.)
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
A solid steel [G= 12900 ksi] shaft with the diameter of d = 1.375 in. is subjected to torques TB = 250 lb.ft, TC = 300 lb.ft, and TD = 140 lb.ft, acting in the directions shown in the figure. Assume a = 48 in., b = 74 in., and c = 40 in. Determine the rotation angle of pulley C with respect to the support at A. In rad
The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. Gst = 10.8(10³) ksi. (Figure 1) Figure sin. A 0.5 in. Jc 8 in D 500 lb-ft 12 in. 1 in. B < 1 of 1 Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μÅ Value 6 Request Answer Units www. ?
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
(8) An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r = 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). 6" (a) At the fillet, compute D and the 30 maximum tensile stress. (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?