A transformer on a pole near a factory steps the voltage down from 3,600 V (rms) to 120 V (rms). The transformer is to deliver 1030 kW to the factory at 92% efficiency. (a) Find the power delivered to the primary. kW (b) Find the current in the primary. A (c) Find the current in the secondary. A

A transformer on a pole near a factory steps the voltage down from 3,600 V (rms) to 120 V (rms). The transformer is to deliver 1030 kW to the factory at 92% efficiency. (a) Find the power delivered to the primary. kW (b) Find the current in the primary. A (c) Find the current in the secondary. A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

DC 200 V was applied to the primary of a transformer with a conversion ratio of 1/5. Obtained from seconderexplain the reason for this by typing the voltage value to be?
26/. a) Compute the e.m.f. induced in the transformer, if the turns ratio is 100 turns/ 25 turns and a flux of 0.3 Wb
Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five customers. Daily maximum demands for these customers are 120 kW, 40 kW, 90 kW, 110 kW, and 180kW. The maximum demand on the feeder is 243kW. The coincident factor of the feeder is
As given in the figure, an ideal transformer feeds a load under 120V voltage. Which of the following is the source voltage (Vs)?
1.) A transformer with a rating 600 KVA has an efficiency 0f 94 percentage at full load and at 1/4TH of full load, with a power factor of 1. Solve and determine the efficiency of the mentioned transformer at 70 percentage of full load and with a power factor of 0.80 lagging.
answer: 5.19 – j2.95 A
6. 150 kVA, 2800-240 V, 50 Hz transformer. Regis = 0.0082N , Xeq.Ls = 0.0223N RfcHs=2200N Step down transformer delivers 135 kW to a load at 0.9 lagging power factor at rated voltage. Determine the Following: a) Terminal voltage (LV side). b) Terminal voltage (HV side). c) High side current. d) Input impedance. e) Voltage regulation. f) Efficiency. g) Voltage regulation for 0.9 leading pf. h) Draw the phasor diagram of secondary circuit at 0.9 lagging pf. i) Draw the phasor diagram of secondary circuit at 0.9 leading pf. XmHs=12002
Vin V₁ leee liee V₂ R₂ ww Vout 1:5 Assume the transformer circuit above is ideal, and that R₁ = 1000, R₂ = 4000 and 11,rms = 50 A. Find the rms voltage, Vzrms, across the secondary coil of the transformer. V2.rms [V]:
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
a) A sinewave is having a frequency of 60 Hz and instantaneous voltage of 100 Volts at 1.5 milli seconds. Find: i) The maximum value of sinusoidal voltage waveform ii) The value of voltage at 2.1 milli seconds. b) An alternating voltage is given by v=300 sin(120TTT +0.25) volts. Find: (i) Peak Value of Voltage (ii) r.m.s Value of voltage (iii) Phase angle in degrees with respect to 300sin(120Ttt). (iv) The instantaneous value of voltage when t=0 (v) Draw the sine wave of 300sin(120tt).
The maximum speed of an alternator working at 60 Hz is possible when the number of poles of the machine is ........ a. 4 b. 5 c. 3 d. 2
1. Find the all-day efficiency of a transformer having maximum efficiency of 96% at 30-kVA load at UPF. If during the day the transformer is loaded as follows: 12 hours.... 6 hours... .5 kW at 0.6 p.f. lagging ..24 kW at 0.8 p.f. lagging 6 hours..... ..at no-load.