A transformer has 1000 turns on its primary side and 500 turns on the secondary side. When a voltage, V of frequency f is connected across the primary winding a maximum flux of 2 x 10-³Wb is produced in the core which links both the windings. Calculate the value of emf induced in the two windings, in terms of f

A transformer has 1000 turns on its primary side and 500 turns on the secondary side. When a voltage, V of frequency f is connected across the primary winding a maximum flux of 2 x 10-³Wb is produced in the core which links both the windings. Calculate the value of emf induced in the two windings, in terms of f

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.5MCQ: For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is...

See similar textbooks

Similar questions

The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
Find out the equivalent inductance for the combination when 2 inductances L1 and L2 are connected in parallel such that their fluxes oppose each other Determine the efficiency of the transformer and find out the value of load at which efficiency will be maximum 3
A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be constant, the applied voltage should be ?
A single-phase transformer has 480 turns on the primary and 90 turns on the secondary. The mean length of the flux path in the core is 1.8 m and the joints are equivalent to an airgap of 0.1 mm. The value of the magnetic field strength for 1.1 T in the core is 400 A/m, the corresponding core loss is 1.7 W/kg at 50 Hz and the density of the core is 7800 kg/m3. If the maximum value of the flux density is to be 1.1 T when a p.d. of 2200 V at 50 Hz is applied to the primary, calculate: a. the cross-sectional area of the core; b. the secondary voltage on no load; c. the primary current and power factor on no load
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
A single phase 60 Hz transformer has its core volume of 1.5x10-3 cu m. The maximum flux density is 1.0 tesla and the hysteresis constant of the core is 6000. find the hysteresis loss.
. A 400/230V, 50Hz, single phase transformer has 200 turns on high voltage side. Find turns ratio, transformation ratio, and number of turns on low voltage winding. Also find the flux developed in the core
A single-phase transformer has 500 turns on the primary and 100 turns on the secondary. The mean length of the flux path in the core is 2.0 m and the joints are equivalent to an air-gap of 0.1 mm. The value of the magnetic field strength for 1.21 T in the core is 400 A/m, the corresponding core loss is 1.8 Watts/kg at 50 Hz and the density of the core is 7850 kg/m3. The cross-sectional area of the core is 0.0187 m2. If the maximum value of the flux density is to be 1.21 T when the nominal rated voltage is applied at 50Hz, calculate the magnitude of the primary current, in amperes, if a load current of 135 A is being supplied at a lagging power-factor of 0.85. Neglect the leakage impedances in the transformer windings.
The voltage per winding of the 220V/12V, 50 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, the cross-sectional area of the core in cm 2 is equal to which of the following. O 0.0050 30 50 O 0.0025 0.0030 O 60 0.0060 O 25