a topical solution calls for 5mg/ml. The pharmacist must prepare 20ml of the solution using ketoconazole powder and 95% alcohol as the diluent. A balance (MAWQ = 0.12g) and 20ml measuring cylinders are available for compounding. The solution will be dispensed in 20ml glass bottle. Describe how you would compound this formulation

a topical solution calls for 5mg/ml. The pharmacist must prepare 20ml of the solution using ketoconazole powder and 95% alcohol as the diluent. A balance (MAWQ = 0.12g) and 20ml measuring cylinders are available for compounding. The solution will be dispensed in 20ml glass bottle. Describe how you would compound this formulation

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter7: Solutions And Colloids

Section: Chapter Questions

Problem 7.44E

See similar textbooks

Similar questions

25mL 10% Na04 salution ? mmol theo mmoldikenzalacetone theo mass divemaaletone mass recovered 1 mmol 26g benzaldehyde. ? ML 2 mmol 7. 0.8mL acetone 2 mmol
How many milliliters of a thimerosal 25% stock solution must be used to prepare 100 ml of thimerosal topical solution of 1:1000 ratio strength? A diphenhydramine elixir contains 12.5 mg drug in one teaspoon. The volume of oral vehicle that is to be added to 100 ml of this elixir to reduce its strength by one half its original strength is: When preparing an ounce of 1% hydrocortisone cream the technician made an error and added 200 mg of hydrocortisone in the preparation. Calculate the additional amount of hydrocortisone powder that should be added to the 1 ounce cream to make the strength 1%. Onabotulinumtoxin A (BOTOX) is available in a 100 units vial for reconstitution. 2.5 ml of sterile preservative free normal saline was added to this vial and reconstituted. How many units of botox is present in 0.1 ml of the dilution? (ignore any volume changes during reconstitution)
Show that mmol of aspirin recovered divided by mmol of limiting reagent x 100% gives the same % yield as calculated above
6.3017g sample was weighted Analytically and made up volumetrically to 500mL. A 25mL alliqout of this solution required a total valume of 41.32mL of 0.0987MHCl to reach bromocresol green endpoint Another 25ml alligout of this salution was treated with 25mL of 0.1014M NaOH react with excess of BaCl₂ solution und left over NaOH required 21.83mL of 0.0987MHCl to reach the phenolpthelin end point. Determine the percentage of Na₂CO3 and. NaHCO3
The solubility of KNO3 at 25°C is 80 g KNO3 / 100g H20. [ Select ] solution a) A solution of 160g KNO3 in 200g of water is a [ Select ] unsaturated saturated supersaturated Stittt J solution b) A solution of 45g KNO3 in 50g of water is a [ Select ] v solution c) A solution of 10g KNO3 in 25g of water is a
In the order: Add 30 mEq to calcium gluconate to 1L D5 1/4NS. 1) How many ml of calcium gluconate 15% w/v injection should be used to prepare this IV order? 2) Assuming volumes are additive and complete dissociation, what would be the osmolarity of the IV admixture solution? (Consider total volume after adding the volume of calcium gluconate.)
Prepare 300 ml of 30%, 50%, 70%, 80% and 90% ethyl alcohol usingformula: C1V1=C2V2 give the complete solution and answer
(72 l l ..:01:EP is متعد د الخيارات What weight is needed to prepare solution of 0.15 N from Na2CO3 in 300 ml of distilled water. Na = 23, C = 12, 0 = 16 %3D 2.385g 3.285g 5.82ml 2.385ml
Describe the preparation of i. 500 mL of 3.50% (w/v) aqueous glycerolii. 500 mL of 2.45%(v/v) aqueous ethanoliii. 5.00L of 0.020M KMnO4 from solid reagent
What weight (in grams) of caffeine (C8H10O2N4) is required to prepare 100 mL each of the following solutions: 1) 0.1 M 2) 7% (w/v) 3) 100 ppm 4) 2mM (show solution)
Prepare 1500mL of 0.5N H2SO4 solution with specific gravity of 1.84g/mL and assay of 97%
SALT SOLUTION: Trial 1: Volume: 25 mLMass of 25mL solution: 29.824 gDensity: 1.2 g/mL Trial 2:Volume: 25 mLMass of 25 mL solution: 29.855 gDensity: 1.2 g/mL Trial 3:Volume: 25 mLMass of 25 mL solution: 29.816 gDensity: 1.2 g/mL METAL BAR: Method I - Trial 1:Mass of metal bar: 57.063 gVolume of metal bar: 6.7 cm^3Density of bar: 8.5 g/cm^3 Trial 2:Mass of metal bar: 57.063 gVolume of metal bar: 6.0 cm^3Density of bar: 9.5 g/cm^3 Trial 3:Mass of metal bar: 57.063 gVolume of metal bar: 6.0 cm^3Density of bar: 9.5 g/cm^3 Method 2 - Trial 1:Dimensions: diameter = 1.20 cm, height = 4.91 cmMass of metal bar: 57.063 gVolume of metal bar: 5.55 cm^3Density of bar: 10.3 g/cm^3 Trial 2:Dimensions: diameter = 1.20 cm, height = 4.95 cmMass of metal bar: 57.063 gVolume of metal bar: 5.60 cm^3Density of bar: 10.2 g/cm^3 Trial 3:Dimensions: diameter = 1.20 cm, height = 4.95 cmMass of metal bar: 57.063 gVolume of metal bar: 5.60 cm^3Density of bar: 10.2 g/cm^3 QUESTION - From your data, calculate the…