A three-stage compressor receives 500 lps of air at 101 kPaa and 27degrees Celcius, and discharges at 750 kPaa. Determine a) the power required; b) the pressure at each intercooler; c) the maximum temperature; and d) the heat transferred in each intercooler. e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?

A three-stage compressor receives 500 lps of air at 101 kPaa and 27degrees Celcius, and discharges at 750 kPaa. Determine a) the power required; b) the pressure at each intercooler; c) the maximum temperature; and d) the heat transferred in each intercooler. e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 20RQ: Welded ______sealed compressors are normally used in household refrigerators.

See similar textbooks

Related questions

Q: Define the Reversible Adiabatic Expansion

A: A process is called reversible only if there is continuous equilibrium between the system and its…

Q: a alll Asiacell The unit of temperature in S.I.-17 * units The unit of temperature in S.I. units is…

A: Note: - As per the guidelines of Bartleby, only one question is allowed to answer so please submit…

Q: 1) In the condenser of the power plant, Ammonia is isobarically condensed to saturated liquid state…

A: 1.

Q: An engineer in a steam power plant is tasked with calculating: a. The isentropic efficiency of the…

A: Given Data, Inlet pressure to the turbine= 6MPa Inlet temperature to the turbine= 500oC Outlet…

Q: A vapor-compression refrigeration system using ammonia as refrigerant is to be used to cool 45,000kg…

Q: Air at 35°C, 105 kPa flows in a 100mm x 150mm rectangular duct in a heating system. If the…

A: Given data: T=35°C=308.2 KP=105 kPaV˙=0.015 m3/sA=100×150 mm2 Need to determine the mass flow rate…

Q: An adiabatic nozzle has Refrigerant-134a at a pressure of 102 psi and temperature of 248°F entering…

Q: A cooling system capacity Fifteen ton refrigeration, operating at 150 kPa in the evaporator, while…

A: Given data as per the question Evaporator pressure =150 kpaCondensor pressure=950 kpaRefrigration…

Q: In a refrigeration plant ammonia enters the expansion valve as a liquid at 32°C and leaves the…

Q: Q3/ A refrigeration unit of 20 T.R uses R-12 as a refrigerant and works between evaporating and…

Q: In the evaporator of an air conditioning system, air flows over finned tubes through with the…

Question

A three-stage compressor receives 500 lps of air at 101 kPaa and 27degrees Celcius, and
discharges at 750 kPaa. Determine

a) the power required;

b) the pressure at each
intercooler;

c) the maximum temperature; and

d) the heat transferred in each intercooler.

e) What is the discharge temperature of a single-stage compressor operating at the same
intake and discharge temperatures?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Air with a pressure of 0.1 MPa and a temperature of 25oC with a flow rate of 5.29 kg/minute enters a three-stage reciprocating piston compressor with intercooler. The air is compressed polytropically (n = 1.3) to reach the pressure of 4 MPa. Calculate: a) The amount of heat transferred to each intercooler? b) How much air is needed for cooling in the intercooler if the allowable maximum temperature changes between the inlet and outlet of the intercooler is 8oC?
(p) W2 T n2 In a four stage compressor, if the pressure at the first and third stage are 1 bar and 16 bar the to the delivery pressure at the fourth stage will be anteiceol y6) 16 bar 70. For a two stage reciprocating compressor, compression from (a) 1 bar (c) 64 bar (d) 256 bar and no pressure losses. If con
A two-stage compressor receives 672 lpm at 140 kPaa and 27 °C and delivers it at690 kPaa. The Compression is polytropic with n = 1.5 and the intercooler is deal. Finda) the power required; b) the intercooler pressure; c) the maximum temperature; d) theheat transferred in the intercooler; and e) the discharge temperature if the compressoris single stage.
Q1. The adiabatic enthalpy drop in a given stage of a multi-stage impulse turbine is 22.1 16° KJ/kg of steam. The nozzle outlet angle is and the efficiency of the nozzle, defined as the ratio of the actual gain of kinetic energy in the nozzle to adiabatic heat drop, is 92%. The mean diameter of the blades is 1473.2 mm and the revolution per minutes is 1500. Given that the carry over factor is 0.88, and that the blades are equiangular (the blade velocity coefficient is 0.87). Calculate the steam velocity at the outlet from nozzles, blade angles, and gross stage efficiency.
iii) the exit area of the nozzle. Take Cp = 1.005 kJ/kg-K and R=287 J/kg-K Q.B3. A heat engine operates between two reservoirs at 400°C and 30°C. Half the power produced by the heat engine is used to drive a Carnot heat pump that removes heat from the cold surroundings at 2°C and transfers it to a house maintained at 27°C. The heat engine is absorbing heat at a rate of 5 kJ/s. i) Draw the complete schematic of the device ii) Determine the thermal efficiency of the heat engine iii) Determine the coefficient of performance of the heat pump iv) Determine the rate of heat loss from the house. v) Determine the minimum rate of heat extraction by the heat pump, and vi) the total rate of heat rejection.
Answer 1.8 and 1.9
Question 2 A two stage, single acting, reciprocating compressor takes in air at a rate of 2 m³/s at a pressure of 1 MPa @ 16°C. The air is compressed to 0.7 MPa while running at 10 rev/s. Compression is ideal and perfect intercooling takes place. The compression process follows pV1.25 = C. Neglect clearance. Calculate: 2.1. Intermediate pressure (0.265 MPa) 2.2. Volume of LP cylinder (20 Liters) 2.3. Volume of HP cylinder (7.5 Liters) 2.4. Total cycle power (42 kW)
A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
I need the answer as soon as possible
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
Air with a pressure of 0.1 MPa and a temperature of 25oC with a flow rate of 5.29 kg/minute enters a three-stage reciprocating piston compressor with intercooler. The air is compressed polytropically (n = 1.3) to reach the pressure of 4 MPa. Calculate: a) The pressure at stage-2 and stage-3 so that the compression work is minimum? b) The compression work in each stage and the total compression work? c) The outlet air temperature from each stage's cylinder? d) The amount of heat transferred to each intercooler? e) How much air is needed for cooling in the intercooler if the allowable maximum temperature changes between the inlet and outlet of the intercooler is 8oC?
QUESTION 25 A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m3/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual nuber to find the intermedia pressure ratios is