A three-phase, Y-connected synchronous generater supplies current of 10 A having phase angle of 20º lagging at 400 V. Find the load angle if Xs = 10 ohms per phase. Assume Rs to be negligible. Also, calculate the total generated real and reactive power.

A three-phase, Y-connected synchronous generater supplies current of 10 A having phase angle of 20º lagging at 400 V. Find the load angle if Xs = 10 ohms per phase. Assume Rs to be negligible. Also, calculate the total generated real and reactive power.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Related questions

Q: Consider the system shown in Figure 1 with G(s) =1/s(s + 1) and ZOH= (1-e) Find out the range of K…

A: Step 1: We've to find the stability of the system, which means we need to analyze its closed-loop…

Q: A, B, C are the inputs, and D, E, F are the outputs. By “completely specified” it means that, for…

A: Let's analyze the state graph and construct the corresponding state table. 1. State Graph…

Q: [Q1] Assume there are 50 signals, each one is band-limited to 10kHz and sampled at a rate 28% over…

A: I can't access the specific image you sent, but based on your description of the circuit being a…

Q: Let 10 fi(t)=5+ cos noot 50 f2(t)=1+sinn nwot a) Find the trigonometric Fourier series coefficients…

A: Step 1:Step 2:

Q: 3. The 6-V zener diode in Fig. 7-12 has a maximum rated power dissipated of 690 mW. Its reverse…

A: (3): If you have any queries, please comment.

Q: Please answer in typing format

A: Step 1: Step 2: Step 3: Step 4:

Q: 02: Using the following discrete sequence definitions -2 x(n) = =1 0 and n = 0,1,2 n = 3,4 elsewhere…

A: In the question it's mention that choose any TWO.so I did by choosing two methods.

Q: How would I complete the truth table usinng the circuit in FIgure 2.1 using 1's and 0's

A: Step 1: Step 2: Step 3: Step 4:

Q: whatever u can thank you!

A: Step 1: This figure can be divided into its electrical equivalent in terms of reluctances and…

Q: Please help with these parctice problems so I may study from them

A: Step 1:The following python code will help to find the impulse responce with these requirements. Low…

Q: Sin (X + cos x)=0.5= Find g(x), g(x)

Q: Say you were trying to find the equivalent resistance based on this circuit. How would v1 be found?…

A: Step 1:Step 2:Step 3:

Q: The total inductance that I got is 2.4H, can you check if my answer is correct?

A: Step 1: As we can see 2 inductance of 4H are connected in parallel. so we get (4||4)=[(4*4)/(4+4)]…

Q: 4) 10% Derive and plot the amplitude spectrum of f (t) = sin 10t. Assume the fundamental frequency…

A: Step 1:

Q: [Q2] What is the power (S) required at the receiver to achieve a channel capacity of 550kbps? Assume…

A: Step 1: Step 2: Step 3: Step 4:

Q: I had asked this question, but i am not sure if it got picked up, if you can solve this it would be…

A: Step 1Step 2 Step 3 Step 4

Q: Example:For the circuit if the switch is at B for along time and moved to A at t=0 sketch Vc for…

A: Step 1:Step 2:Step 3:Step 4:

Q: Calculate the magnetic flux created by the field lines uniform magnetic force of 27 passing through…

Q: Pls show neat and whole solution

A: Step 1:Step 2:Step 3:

Q: EXERCISE 14.3.9 (a) Find (t) fort > 0 in the circuit below. 10 V + t = 0 802 202 1/3 H io(1) ww 3/8…

A: Step 1: for t<0 for long time capacitor acts as open circuit and inductor acts as short circuit…

Q: the shift of the asynchronous machine gives information about the operating status of the machine.…

A: Step 1: Step 2: Step 3: Step 4:

Q: Q.5: Find the Laplace Transform of the following. L[et cos 3t9t ³ +π]

A: Step 1:

Q: Write (but don't solve) the current equations for: ≥6 3 Z MM 4 www 11 7 12 10 4mn १ 8

A: Circuit Diagram:By applying Khrichoff's voltage law in loop 1, we can write−5+6i1=0 By applying…

Q: I = 5.76mA∠43.91° VR = IZR = (5.76mA∠43.91°)(1kΩ∠0°) = 5.76V∠43.91° VL = IZL =…

A: Step 1:

Q: The current through a 5-mH inductor is shown in the Figure. Determine the sign and magnitude of the…

Q: 2.2 A vector p is 10 units long and is perpendicular to vectors q and r described here. Express the…

A: Step 1: Step 2: Step 3: Step 4:

Q: 12. Please answer need solution thanks!

A: Kindly see attached photo.

Q: The final nodal equation obtained from node 2 is Blank 1 = Blank 2 v1+Blank 3 V2 +Blank 4 V3Enter 3…

A: Step 1:

Q: 4. Calculate the average output value of a fully controlled 24-pulse thyristor converter feeding…

Q: please solve a to c detailed step by step solution thank you

A: Step 1:(a)Direct Form I structure:In the direct form I structure, the system function is implemented…

Q: Vll=164v IL=0.48A P1=75W P2=75W Pinput=150w please solve question 5 in discussion section

A: Step 1:Step 2:Step 3:

Q: 04. Write the necessary mesh equations for the circuit shown in Fig. Q10.04. E2 1/1/2 R2 w R3 www R1…

A: Step 1: Step 2: Step 3: Step 4:

Q: Please help with this parctice problems so I may study

A: a) To determine if the filter is Type I or Type II, we need to look at the symmetry properties of…

Q: . The phase margin (in degrees) of a system having the loop transfer functions G(s)H(s) = 2√3 s(8+1)…

Q: Please help with these parctice problems so I may study from them

A: I can help you with the general concepts of Nyquist sampling theorem and its…

Q: Use the voltage divider rule to calculate the voltage Vab and record it in the second column of…

A: Step 1:

Q: A current is set up in a wire loop consisting of a semicircle of radius 4.08 cm, a smaller…

A: Step 1:Step 2:So, the radius of the smaller semicircle is 2.02 cm

Q: A 40-kVA, 240-V, 50-Hz, 4-pole, three-phase, Y-connected alternator has a synchronous reactance of…

A: Step 1:Step 2:Step 3:

Q: 4. The transistor in the amplifier below has been biased such that IC - 0.3mA (no need to do DC…

A: Step 1:Step 2:Step 3:

Q: Abalancedstarconnectedloadisconnectedtoa4kVA,415V,starconnectedthreephasegeneratorviaathreewiretran…

A: To solve this problem, we can follow these steps:1. Calculate the current and power of the balanced…

Q: Please answer in typing format

A: Step 1: Step 2: Step 3:

Q: By hand, evaluate the complex Fourier series coefficients of your noise function. Typesetthe noise…

Q: The capacitor in the below circuit was discharged prior to assembly and the circuit was in steady…

A: Based on the image you sent, the circuit appears to be a voltage divider circuit with an additional…

Q: Using the diagram capacitor circuit and values provided, find ZC1, Z T, i, VR1, and Vc1

Q: Exercise 2: Series connection of four-terminal networks Fig. 2b shows a series connection…

A: 1. The Z matrix for the series connection of two Γ-quadripoles II can be found using the following…

Q: please solve questions 1 to 4 in the calculations section thank you

A: Step 1: Step 2:

Q: Please answer in typing format

A: To solve this, we'll first find the total impedance of the circuit, which is the sum of (R1) and…

Q: Q.4: Find the Laplace Transform £ { 4e-41 √ ² dt} `t sin h(t) dt

A: Step 1:

Q: 3.27. Using the S sequence definitions h(k) = 2,0,1,2 amstags wolle sito 1,= 3,4 and x(k) S 0…

A: Step 1:Step 2:Step 3:Step 4:

Q: الموضوع : EX21 Ex2/ find Fes of S+I S + (S+2 H.w (S+212

A: Step 1:

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a non-sinusoidal current i(t). The voltage and current waveforms are shown below. Assume any values of your choice for Vp (≤ 200 V) and Ip (≥ 5 A). 1. calculate the average power and net power factor of the load. 2. The total load harmonic distrotion (THD) of the load current, assuming the smallest frquency term as fundamental.
two generators supplying a load. Generator I has a no-load frequency of 62.5 Hz and a slope Sp1 of I MW/Hz. Generator 2 has a no-load frequency of 62.0 Hz and a slope sp2 of I MW/Hz. The two generators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. (a) At what frequency is this system operating, and how much power is supplied by each of the two generators? (b) Suppose an additional I-MW load were attached to this power system. What would the new system frequency be, and how much power would Gl and G2 supply now? Generator 1 VT V2 Generator 2 VTí KVAR KVAR
Which of the following descriptions IS NOT correct for loads in power systems? A. The purely resistive load absorbs the real power from the power grid B. The purely inductive load absorbs the positive reactive power from the power grid C. The purely capacitive load absorbs the positive reactive power from the power grid. D. The average value of the instantaneous power through loads is equal to its real power. In an ac circuit, power factor correction or improvement is achieved by A. Connecting a resistor in parallel with the inductive load B. Connecting an inductor in parallel with the inductive load C. Connecting a capacitor in parallel with the inductive load A balanced delta-load can be converted to an cquivalent balanced wye- load by dividing the delta-load impedance by A. square root of 3 В.3 C. 1/3
A synchronous generator is rated 645 MVA, 24 kV, 0.9 pf lagging. It has a synchronous reactance 1.2 . The generator is feeding full load at 0.9 pf lagging at rated voltage. Calculate: (a) Excitation emf (E,) and power angle 8 (b) Reactive power drawn by the load Carry out calculations in pu form and convert the result to actual values.
A single-phase motor draws 180 W at a power factor of 0.8 lagging when connected across a 240 Vrms, 60-Hz source. A capacitor is connected in parallel with the load to produce a unity power factor. Determine the required capacitance. The required capacitance = ____ μF.
Three single-phase transformers are connected in delta-delta to step down a line voltage 138 kV to 80 kV to supply a manufacturing plant. The plant draws an active power of 24 MW at a lagging power factor of 0.89. Calculate apparent power in MVA drawn by the plant.
If, in one (360 degrees), all of the instantaneous power falls under positive loops (no negativeloops), the load must be:a. A resistorb. An inductor or capacitorExplain:
A 400-V, 3-phase induction motor load takes 900 kVA at a power factor of 0.707. Calculate the KVA rating of the capacitor bank to raise the resultant power factor of the installation of 0.866 lagging. Find also the resultant power factor when the capacitors are in circuit and the motor load has fallen to 300 kVA at 0.5 power factor.
A three phase load has a rating of 200 KW, 4000 volts, 0.7 power factor lagging and a frequency of 50 Hz. Determine the required capacitor bank rating in micro Farad per phase to improve its power factor to 0.9 lagging if: a) The capacitor bank is to be connected in Delta. b) The capacitor bank is to be connected in Star.
a load of 15 mva with power factor 0.86 lagging is given. Calculate the reactive power delivered by shunt capacitors to increase power factor to 0.9 lagging
A single-phase power system is shown as the equivalent circuit below. The system has a 480V generator connected to an ideal 1:10 step-up transformer (no losses), a transmission line, an ideal 20:1 step-down transformer and a load all in series as shown. The resistance of the transmission line is 20 S2 and the reactance j60 , a load is connected to the system with an impedance of 10/30° №. For the analysis of the system, use base values of 10 kVA and 480 V at the generator, find (a) per unit values of all impedances, (b) per unit current, (c) load power (W), (d) power loss (W). NG 480 20⁰ V 10 kVA Zone 1 1:10 20 Ω j60 Ω ZL Zone 2 20:1 ILoad Zone 3 ZLoad 10/30° Ω