A single-phase power system is shown as the equivalent circuit below. The system has a 480V generator connected to an ideal 1:10 step-up transformer (no losses), a transmission line, an ideal 20:1 step-down transformer and a load all in series as shown. The resistance of the transmission line is 20 S2 and the reactance j60 , a load is connected to the system with an impedance of 10/30° №. For the analysis of the system, use base values of 10 kVA and 480 V at the generator, find (a) per unit values of all impedances, (b) per unit current, (c) load power (W), (d) power loss (W). VG 480 0⁰ V 10 kVA Zone 1 1:10 20 Ω j60 Ω ZL Zone 2 20:1 ILoad Zone 3 ZLoad 10/30° Ω

A single-phase power system is shown as the equivalent circuit below. The system has a 480V generator connected to an ideal 1:10 step-up transformer (no losses), a transmission line, an ideal 20:1 step-down transformer and a load all in series as shown. The resistance of the transmission line is 20 S2 and the reactance j60 , a load is connected to the system with an impedance of 10/30° №. For the analysis of the system, use base values of 10 kVA and 480 V at the generator, find (a) per unit values of all impedances, (b) per unit current, (c) load power (W), (d) power loss (W). VG 480 0⁰ V 10 kVA Zone 1 1:10 20 Ω j60 Ω ZL Zone 2 20:1 ILoad Zone 3 ZLoad 10/30° Ω

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

urgent required.
Solve it quickly please
In an installation there is a three-phase load of 300 kVA with a power factor of 0.8 behind, in parallel with a three-phase load of 150 kVA with a power factor of 0.6 ahead. A pure reactive element is connected in parallel, and a unity power factor is obtained at the power input. Indicate the reactant of the element, with a positive sign if it is a bank of reactors, or with a negative sign if it is a bank of capacitors. Just put the corresponding sign followed by the numerical value, without units. The numerical value must correspond to the three-phase kVARS. You can use integer values with no decimal places or up to two decimal places
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 13.2 (line-to-line) kv. The step-down transformer has a turn ratio of 15:1 and it has a Y-connected, balanced load of 0.667 +j 0.111 ohms connected to its secondary side. A capacitor bank of -j0.239 ohms is added parallel to the load. Assuming an ideal transmission line, the effective impedance of the system (per phase) seen by the source would be: O A. 0.093 + j0.249 O B. 0.372 + j0.996 OC.3.72 + j9.96 O D. None of the other choices are correct O E. 0.186 + j0.498
1 Two transformers A and B are connected in parallel to a load of (2+j1.5)2. Their impedances in secondary terms are ZA = (0.15 + j0.5)2 and ZB= (0.1 +j 0.6)2. Their no-load terminal voltage are EA 207 /0° volt and EB = 205/0° volt. Find the power output and power factor of each transformer.
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
Two single-phase transformers, having equal turns ratio, in parallel supply a secondary load of 1,000 A at 0.8 pf lagging. For each transformer the secondary emf on open circuit is 3,300 V and their total leakage impedances referred to secondary are (0.10 + j0.20) ohms and (0.05 + j0.040) ohm, respectively. Determine the output current on each transformer.
For a 50 kVa distribution transformer, which on its high voltage side is 2400 V and on the short-circuit low voltage secondary has a voltage of 240 V with a frequency of 60 Hz, it has a leakage impedance of 0.72+j0.92 Ω on the high voltage side and 0.0070+j0.0090 Ω on the high voltage side low tension. The short-circuit test presented values of 48 V, 20.8 A and 617 W for high voltage. The impedance responsible for the excitation current is 6.32+j43.7 Ω referring to the low voltage side. One open circuit test, with the low voltage side energized, presented the values of 240 V, 5.14 A and 186W. According to the information presented, determine: a. Draw the equivalent circuit on the high voltage side and present the impedance values in the circuit. b.Draw the equivalent circuit on the low voltage side and present the impedance values in the circuit. c. For the high voltage value, calculate the value of the current flowing in the magnetizing impedance. d.Determine the yield for an…