A three-phase unbalanced source with the following phase-to-neutral voltages 2. 200 /25° 100 L-155° Vabc 80 Z100° is applied to the circuit Zm Va Zn The load series impedance per phase is Z,= 8+ j24 and the mutual impedance per phase is Zm=j4. The load and source are fully grounded. Determine (a) the load sequence impedance matrix Z,=A'Z„A (b) the symmetrical component of voltage (c) the symmetrical components of current (d) the load phase currents (e) the complex power delivered to the load in terms of symmetrical components Sp = 3(V,I, + V1l¡ +V½I¿).

A three-phase unbalanced source with the following phase-to-neutral voltages 2. 200 /25° 100 L-155° Vabc 80 Z100° is applied to the circuit Zm Va Zn The load series impedance per phase is Z,= 8+ j24 and the mutual impedance per phase is Zm=j4. The load and source are fully grounded. Determine (a) the load sequence impedance matrix Z,=A'Z„A (b) the symmetrical component of voltage (c) the symmetrical components of current (d) the load phase currents (e) the complex power delivered to the load in terms of symmetrical components Sp = 3(V,I, + V1l¡ +V½I¿).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

18. A 415 V, 50 Hz, 3-phase supply of phase sequence RYB is connected to a delta connected load in which branch RY consists of R, = 100. branch YB conists of R₂ = 20 2 in series with X₂ = 60 Q and branch BR consists of a capacitor C= 30 uF. Take Vy as the reference and calculate the line currents. Draw the complete phasor diagrams. (Elect. Machines, A.M.I.E. Sec. B. 1989) 14.54, 1, 10.66 2172,92, 14.46 2-471 (1 = 7.78
The 3-phase power equation in terms of phase voltage and phase current is /3VplpCoso 3VplpCoso
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
a system that has all zeros and poles in the left half of s-plane represents minimum phase systems ? T F -----------------
12. Two transformers, A and B re connected in parallel on both the HV side and the LV side. Show that the load supplied by each transformer is given by SA =S- ZA+ ZB ZB and Sg = S- ZA ZA +ZB where SĄ and ZĄ are the load and the impedance of transformers A, Sgand Zgare the load and impedance of transformer B, and Sis the total load.
Line Voltages at the terminal Pz:- The of abaancat Y conmected load is----- Each Phase of the load cousist of loL30 S2 Find the active s Reactive and somflex Power fer Phase then Find the total load. Var=12010, Powers for Heree phase
i need the answer quickly
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
A balanced load is connected in star across a 3 phasec415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inducrance 0.5 henry in paeallel with a purw resistance of 28 ohms and a pure capaciror of 60microfarads capacitance ,in each branch. Calculate a. The line currents? Need full working and answer has to be 9.3A Formola for inductance XL= 2×3.142FL FORMOLA FOR CAPACITOR XC= 1/2×3.142×FC
Solve in detail to understand