A three-phase transmission line is designed to deliver 190.5-MVA at 220-kV over a distance of 63 Km. The total transmission line loss is not to exceed2.5 percent of the rated line MVA. If the resistivity of the conductor material is2.84 x 10-8 Q-m, determine the following:a) The resistance of the conductorb) The required conductor diameterc) The conductor size in circular mils.Neglect the power losses due to insulator leakage currents and corona.

Answered: Image /qna-images/answer/b763c8b8-ede9-4fcb-b418-b13a7e0c3379.jpg

A three-phase transmission line is designed to deliver 190.5-MVA at 220- kV over a distance of 63 Km. The total transmission line loss is not to exceed 2.5 percent of the rated line MVA. If the resistivity of the conductor material is 2.84 x 10-8 2-m, determine the following: a) The resistance of the conductor b) The required conductor diameter c) The conductor size in circular mils. Neglect the power losses due to insulator leakage currents and corona.

A three-phase transmission line is designed to deliver 190.5-MVA at 220- kV over a distance of 63 Km. The total transmission line loss is not to exceed 2.5 percent of the rated line MVA. If the resistivity of the conductor material is 2.84 x 10-8 2-m, determine the following: a) The resistance of the conductor b) The required conductor diameter c) The conductor size in circular mils. Neglect the power losses due to insulator leakage currents and corona.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The total conductor cross section of a 537.40 kV (Peak value) three-phase overhead line with a length of 100 km is 517 mm2 and the conductor diameter is 29.6 mm. The roughness factor of the conductors is 0.8 and the distance between the conductors is 6 m. The ambient pressure along the line is 650 mmHg and the temperature is 15oC. Since there is corona discharge in only 5 km of this line, find the total Corona loss lost to the line using the Peek equation (Ed=30kVpeak/cm for Air). I would be very happy if you could be quick. :)
1. A Single-phase, two-wire overhead line has solid cylindrical copper conductors with 2.4 cm diameter. The conductors are arranged in a horizontal configuration with 3 m spacing. Calculate the inductance of each conductor due to both internal and external flux linkages in mH/km. (
The following figure illustrates the configuration of a two-bundle and completely transposed transmission line system operating at 50 Hz. The transmission line length is 100 km, and each bundle consists of conductors with a diameter of 6.0 mm. The resistance of each bundle is 0.12 22 per kilometer. Answer the following questions. a) The inductance in H/m for each phase of the transmission line. b) The total inductive reactance in 2 for each phase of the transmission line. c) The capacitance in F/m for each phase of the transmission line. d) The total capacitive reactance in 92 for each phase of the transmission line. e) Sketch the nominal- circuit of the line 3m 3m 0.06 m 8m
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1cm diameter. The conductors are arranged in a horizontal configuration with 0.71 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux link- ages, and (c) the total inductance of the line.
Given a three-phase load of 125 MW at power factor of 0.8 lagging, operating at 69kV, with a transmission line efficiency of 97% and voltage regulation of 95%, and the line length of 50 km, design a transmission line system and determine the best conductor configuration, conductor resistance and inductance, and conductor radius values to achieve the efficiency and voltage regulation set. Assume a two-bundled conductor configuration with GMR of 0.0496 m and bundle spacing of 30 cm.
Problem 1 a- Explain the meaning of the term "bundle conductor transmission line" and discuss the effects of its use on the electrical performance of a high voltage electric transmission line. b- Consider an experimental 1800 kV three phase bundle-conductor line with parameters A= 0.95 and B=j 70. Determine the value of the parameter C of the line. Assume that the line is delivering 2,000 MVA at receiving end whose voltage of 1750 kV and unity power factor. Determine the sending end voltage of the line. d- C- Determine the sending end current of the line.
Question 1) A 154 kV transmission line has a length of 100 km. The line and the conductors are given in Figure 1. The line is operated at f= 50 Hz. For both old and new lines calculate; a. GMD and GMR. b. Inductance of the line in Henries (H). c. Series Impedance (Z) of the line in Ohms. d. *Compare the results for both lines and comment on the results. e. *If the distance between the two neighbouring conductors is increase from 13 meters to 15 meters what would be the parameters in part a.,b. and c. comment on the results. New Line's Conductors 13 m 13 m Old Line's Conductors d r = 2 cm d = 40 cm r = 2 cm Figure 1
Select the best transmission line from the following: Select one: a. Conductors with very low ohmic characteristics only. b. Insulators with very small conductivities only. c. Conductors with very high conductivities and insulators with very small conductivities. d. Conductors with very high ohmic characteristics and dielectrics with negligible conductivities. e. Insulators with very small| ohmic characteristics only.
A) Two conductors of a single phase line, each of 1 cm diameter, are arranged in a vertical plane with one conductor mounted 1 m above the other. A second identical line is mounted at the same height as the first and spaced horizontally 0-25 m apart from it. The two upper and the two lower conductors are connected in parallel. Determine the loop inductance per km of the resulting double circuit line.
Write any four methods of voltage control and Draw the basic block diagram of AC – DC transmission system. and A transmission line has a span of length 250 m and the weight of the conductor per metrelength is 0.63 Kg. The tension in the conductor is 1250 Kg. Calculate the sag and heightabove the ground at which the conductor should be supported. Consider the groundclearance required is 13m
please help solve this question A 100 km Three-Phase 50 Hz transposed transmission line is composed of bundle of three ACSR, 1,431,000 cmil, 47/7 Bobolink conductors as shown in Figure 2 (a). The Three-Phases (bundled Conductors) have flat horizontal spacing of 11 meters as shown in the Figure 2(a). The conductors have a diameter of 3.8 cm and a GMR of 1.5 cm. The Line is going to be replaced with a six conductor bundle of ACSR, 477,000 cmil, 26/7 Hawk conductors. The conductors have a diameter of 2.5 cm and a GMR of 0.9 cm. The new line will have a horisontal phase spacing of 14 meters as it is going to be operated at higher Voltage rating. The new line is shown in Figure 2 (b). The spacing between the bundles in Figure 2 (a) and (b) is 45 cm. Determine,a) The capacitance for each case and the percentage change in capacitanceb) The inductive reactance for each line and the percentage change.c) The inductance for each case and the percentage change ininductance