A three phase 300km long line has a total series impedance of 200/90° ohms per phase and a total shunt admittance of 0.0013290° Siemens per phase to neutral. If the sending end voltage is 220kV and if the line supplies a loaf of 60MW at 0.8pf lagging, determine the receiving end voltage and current.

A three phase 300km long line has a total series impedance of 200/90° ohms per phase and a total shunt admittance of 0.0013290° Siemens per phase to neutral. If the sending end voltage is 220kV and if the line supplies a loaf of 60MW at 0.8pf lagging, determine the receiving end voltage and current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. Determine the sending-end voltage, current, power factor, and real power. 2= 40 +j175 0 and a total shunt admittance Y i10'S. The line delivers 3 MW at 220 kV and 0.9 power factor lagging. 9.34 A three-phase, 60-Hz, 300-mi transmission line has a total series impedance a. Determine the sending-end voltage, current, power factor, and real power.
A 3-phase, overhead transmission line has a total series impedance per phase of 200 ohms and a total shunt admittance of 0.0013 siemens per phase. The line delivers a load of 80 MW at a 0.8 pf lagging and a 220 kV between the lines. Determine the sending end line voltage and current by Rigorous method.
single phase line operating at 50Hz consist of 2, 12strand copper conductors with 1.5 spacing. line length is 32km. calculate total inductance and total inductive reactance, given GMR of 12 strand conductor is 0.533cm
A three-phase 765 kV, 60Hz, 300 km, line has the following positive sequence impedance and admittance: z=0.0165+j0.3306-0.3310<87.14° 22/km, y=j4.674x10-6 S/km. Identical shunt reactors (inductors) are connected from each phase conductor to neutral at both ends of the 300-km line during light load conditions, providing 50% compensation. The reactors are removed during heavy load conditions. Full load is 1.8 kA at unity p.f. and at 730 kV. Assuming that the sending- end voltage (Vs) is constant, determine the following: a) ABCD parameters of nominal circuit b) Sending end voltage (Vs) and current (Is) c) Percent voltage regulation of the uncompensated line d) Percent voltage regulation of the compensated line
one circuit of a sinlge phase transmission line is composed of three solid 0.5 cm radius wires. the return circuit is the composed of two solid 2.5 cm radius wire . the arrangement of conductors is as shwon in figure below. applying the concept of GMD and GMR , find the inductance of the complete line in millihenry per kilometer
2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20 + j52) ohms and the total phases-neutral admit- tance is 315 microsiemens. Shunt leakage may be neglected. Using the nominalT approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in voltage at the receiving end.
Sciences- Ibra atform Quick Links - FAQS - TRC My courses - > Lab Viva > Lab Viva MCQ Question 10 Not yet answered Marked out of 0.50 F Flag question In a synchronous generator, choose what happens to number of poles if the value of frequency is increased O a. The number of poles will decrease b. The number of poles will be doubled c. The number of poles will increase O d. none of these options Previous page < Laboratory Health and Safety Orientation Semester 2 AY 2020-21 Submit Power Poi Jump to...
The parameters of a three-phase line 200 km long are resistance/km =0.15 , inductive/km=0.5 and capacitive susceptance/km 2 x 10^6 ohm. The transmission line is delivering 50 MVA at 132 kV with power factor 0.85 lagging. Use nominal T method to determine; 1) sending end voltage 2) sending end current 3) sending end power factor 4) transmission efficiency and 5) voltage regulation.
1. Following are types of Transmission Lines EXCEPT A. Medium Line B. Long Line C. Capavitive Line D. Short Line 2. What is the theory used to express the voltage and current relations? A. Per-Phase B. Equavalent Transmission Line Model C. Two Ports Network 3. A 300km transmission line is considered as A. Long Line B. Medium Line C. Short Line 4. For a short transmission line, values for element A B C and D are A. A=1, B=0, C=Z, D=1 B. A=1, B=Z, C=0, D=1 C. A=0, B=Z, C=1, D=1
please help solve this question A 100 km Three-Phase 50 Hz transposed transmission line is composed of bundle of three ACSR, 1,431,000 cmil, 47/7 Bobolink conductors as shown in Figure 2 (a). The Three-Phases (bundled Conductors) have flat horizontal spacing of 11 meters as shown in the Figure 2(a). The conductors have a diameter of 3.8 cm and a GMR of 1.5 cm. The Line is going to be replaced with a six conductor bundle of ACSR, 477,000 cmil, 26/7 Hawk conductors. The conductors have a diameter of 2.5 cm and a GMR of 0.9 cm. The new line will have a horisontal phase spacing of 14 meters as it is going to be operated at higher Voltage rating. The new line is shown in Figure 2 (b). The spacing between the bundles in Figure 2 (a) and (b) is 45 cm. Determine,a) The capacitance for each case and the percentage change in capacitanceb) The inductive reactance for each line and the percentage change.c) The inductance for each case and the percentage change ininductance
Assuming the voltage at the utility bus is 13.5 kV and the PV plant supplies 4.8 MW of power at 0.95 power factor lagging. Draw the diagram of the system and determine i) the per-phase voltage and current at the POI at the PV plant ii) the reactive power delivered and that which is lost in the line. Assume the line is modelled as a short line.