A three-legged stool has one leg of aluminum, one of copper, and one of steel. The legs have the same dimensions. If the load on the stool is on its exact center, which leg is under the greatest stress and which under the least stress? Which leg experiences the greatest strain and which the least strain?

A three-legged stool has one leg of aluminum, one of copper, and one of steel. The legs have the same dimensions. If the load on the stool is on its exact center, which leg is under the greatest stress and which under the least stress? Which leg experiences the greatest strain and which the least strain?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Assume Young's modulus of a femure bone of an effective diameter 2.5 cm is 1.5 x1010 N/m2. The bone breaks if a stress greater than 2 x10° N/m² is imposed on it. What is the maximum force that can be exerted on it?
An aluminum wire 1.50 m long has a diameter of 0.750 mm. If a force of 60.0 N is suspended from the wire find teh stress on the wire, the elongation of the wire, and the strain of the wire. Aluminum = 7.0 n/m^2 x 10^10
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P 35 kips is applied to the assembly at A, two loads of Q = 25 kips are applied at B, and two loads of R = 34 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 35 ksi. The normal stress magnitude in brass rod (3) must be limited to 21 ksi. Determine the minimum diameter required for each of the three rods. P d₁ d2 d3 = || = = i i 1 1 i 1 B Q с in. in. in. R R D
For the connection shown, the average shear stress in the 19-mm-diameter bolts must be limited to 275 MPa. Determine the maximum load Pthat may be applied to the connection. O 642 kN O 349 kN O 428 kN O 468 kN O 380 kN
Consider a steel bolt as a cylinder with a diameter of 3.41 cm and length of 13.8 cm. A shear or shear stress of 313 MN/m 2 is applied to the bolt, which causes it to twist along. What is the angle (in rad) that makes the bolt twisted with respect to its original shape (when it was right)? Note: Ssteel = 8.4 x 10 10 N/m 2.
An elevator is suspended by a steel cable of diameter 2.5cm. The steel has an ultimate tensile stress of 860 MPa. The elevator weighs 500kg. What is the maximum upward acceleration the elevator could have before the cable breaks? (Hint: First work out an equation for the tension in the cable when the elevator is accelerating.) Answer:
A 242-N object is hung from the end of a wire of cross-sectional area 0.01 cm2. The wire stretches from its original length of 150 cm to 150.5 cm. What is the stress on the wire?
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Both rods AB and BC have the same diameter of 50 mm, determine the normal stress on (a) Rod AB (b) Rod BC A B 50 kN 50 kN C 40 kN
A 1.2 x 10-³-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.4 x 10⁹ N/m² and a radius of 18 x 10 m. Suppose that a 65-kg person is hanging vertically on an aluminum (Young's modulus 6.9 x 1010 N/m²) wire. What is the radius of the wire that would exhibit the same strain as the spider's thread, when the thread is stressed by the full weight of the spider? Number i Units
Á brass wire (Y = 10" N/m²) and a steel %3D wire (Y = 2 x 10" N/m²) of equal length and diameter are suspended from a common rigid support. The free ends A of brass and B of steel at a distance of 75 cm are connected by a %3D horizontal bar, with both the wires vertical and parallel. Calculate the distance of a point from B, at which a load may be attached so that the bar remains horizontal. 75cm (75-x) P,
The total cross-sectional area of the load-bearing calcified portion of the two forearm bones (radius and ulna) is approximately 2.0 cm2. During a car crash, the forearm is slammed against the dashboard. The arm comes to rest from an initial speed of 80 km/h in 4.5 ms. If the aum has an effective mass of 3.0 kg, what is the compressional stress that the arm withstands during the crash? Pa Need Help? Read It
An aluminum wire of length 4.3 m and diameter 2.5 mm is connected to a steel wire of length 3.1 m and diameter 1.3 mm. Calculate the change in length (in mm) of this composite, if an object of mass 4 kg is hung from one end. The Young's modulus for aluminum is 7 ×× 1010 N m-2, and the Young's modulus for steel is 20 ×× 1010 N m-2.