A thin straight rod made of an unknown metal has an length of exactly 30.00 cm at 15°C When heated to 95°C, the rod lengthens by 0.041 cm. Determine the coefficient of linear thermal expansion a of the metal. O (2.5 x 10-5)C O (1.7 × 10-5)/C O (2.1 x 10-5)/C O (1.3 × 10-5)/C (9.4 x 10-4)/C

A thin straight rod made of an unknown metal has an length of exactly 30.00 cm at 15°C When heated to 95°C, the rod lengthens by 0.041 cm. Determine the coefficient of linear thermal expansion a of the metal. O (2.5 x 10-5)C O (1.7 × 10-5)/C O (2.1 x 10-5)/C O (1.3 × 10-5)/C (9.4 x 10-4)/C

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter16: Temperature And The Kinetic Theory Of Gases

Section: Chapter Questions

Problem 14P

See similar textbooks

Similar questions

A construction worker uses a steel tape to measure the length of an aluminum support column. If the measured length is 18.700 m when the temperature is 21.2C, what is the measured length when the temperature rises to 29.4C? Note: Dont neglect the expansion of the tape.
(a) Estimate the specific heat capacity of sodium from the Law of Dulong and Petit. The molar mass of sodium is 23.0 g/mol. (b) What is the percent error of your estimate from the known value, 1230 J/kg ? `
What is me Fahrenheit temperature of a person with at 39.0°C fever?
(a) Find the density in SI units of air at a pressure of 1.00 atm and a temperature of 20 , assuming that air is 78% N2, 21% O2, and 1% Ar, (b) Find the density of the atmosphere on Venus, assuming that it's 96% CO2 and 4% N2, with a temperature of 737 K and a pressure of 92.0 atm.
A hollow aluminum cylinder 20.0 cm deep has an internal capacity of 2.000 L at 20.0C. It is completely filled with turpentine at 20.0C. The turpentine and the aluminum cylinder are then slowly warmed together to 80.0C. (a) How much turpentine overflows? (b) What is the volume of the turpentine remaining in the cylinder at 80.0C? (c) If the combination with this amount of turpentine is then cooled back to 20.0C, how far below the cylinders rim does the turpentines surface recede?
Hot water (cp-4.18 kJ/kg.K, m= 2.2 kg/min) flows inside a tube (inner diameter = 9 mm, Length = 93 cm, thickness =1.0 mm, kb = 40 W/m.K), if the heat flux on the tube outer surface is 325 kW/m. What is the temperature drop of water (C)? tube Select one: O A. 66.26 O B. 71.79 O C. 69.97 O D. 64.43 O E. 68.15
A cylindrical metal boiler of radius 10 cm and thickness 3.14 cm is filled with water and placed on an electric heater. If the water boils at the rate of 50 g s', estimate the temperature of the fila- ment. Thermal conductivity of metal 102 w m K- and latent heat of vaporisation = 2.26 x 10° J g'. = 1.13 × %3D
A steam pipe is covered with 1.50-cm-thick insulating material of thermal conductivity 0.200 cal/cm . °C . s. How much energy is lost every second when the steam is at 200.°C and the surrounding air is at 20.0°C? The pipe has a circumference of 800. cm and a length of 50.0 m. Neglect losses through the ends of the pipe.
What is the change in length in millimeters of a 3.00-cm-long column of mercury if its temperature changes from 29.0°C to 43.0°C, assuming the mercury is unconstrained lengthwise? mm
A). How much heat transfer (in kcal) is required to raise the temperature of a 0.550 kg aluminum pot containing 2.00 kg of water from 20.0°Cto the boiling point and then boil away 0.700 kg of water? B). How long (in s) does this take if the rate of heat transfer is 600 W (1 watt = 1 joule/second (1 W = 1 J/s))?
An aluminum beam is 10.0 m long at a temperature of 25.0 °C. The temperature of the beam is raised to 75.0 °C. What is the change in the length of the beam due to thermal expansion, if aluminum has a coefficient of linear expansion of 2.40 E 5 °C-¹?
How much heat is conducted in one hour through an iron plate 2.0 cm thick and 100 cm2 in area, the temperature of the two sides being kept at 0 and 20°C? COMPLETE FBD SOLUTION AND REQUIREMENTS PS. THIS IS A HEAT TRANSFER PROBLEM