kindly solve asap A thin semi-circular pipe has been bent in the shape of a semicircle of radius R and is held fixed. Anideal spring is inserted inside the pipe as shown in figure. Two balls, each of mass m, are released attwo ends of the pipe and the system is allowed to settle in equilibrium (see second figure). Inequilibrium, compression in the spring is found to be x. Find force constant (k) of the spring.verticaldown(A) k=-mg(B) k =-mgcoscos2.x2RR(C) k =mg(D) k=mgcoscos2x2R2R

Draw the free body diagram of the of the given arrangement: Note from the figure: θ=x2R=x2R

A thin semi-circular pipe has been bent in the shape of a semicircle of radius R and is held fixed. A ideal spring is inserted inside the pipe as shown in figure. Two balls, each of mass m, are released two ends of the pipe and the system is allowed to settle in equilibrium (see second figure). equilibrium, compression in the spring is found to be x. Find force constant (k) of the spring. vertical down mg cos R mg (A) k =- cos (B) k= 2x 2R (C) k = mg (D) k=- mg cos cos 2x 2R 2R

A thin semi-circular pipe has been bent in the shape of a semicircle of radius R and is held fixed. A ideal spring is inserted inside the pipe as shown in figure. Two balls, each of mass m, are released two ends of the pipe and the system is allowed to settle in equilibrium (see second figure). equilibrium, compression in the spring is found to be x. Find force constant (k) of the spring. vertical down mg cos R mg (A) k =- cos (B) k= 2x 2R (C) k = mg (D) k=- mg cos cos 2x 2R 2R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

.Learning task 3.2 For a No. 7 ball bearing, the New Departure Handbook states that the maximum boreshould be 1.3780 in. and the minimum, 1.3775 in.; for average conditions, the shaftshould have a maximum diameter of 1.3784 in. and a minimum of 1.3779 in.Determine the corresponding tolerances and allowances.
1-Show how the roughness is indicated for a Surface to be coated, obtained by any production method with N6 showing max. and min roughness. 3- gearing is suitable for two shafts at 90°. : Draw five turns of a compression spring of wire diameter 6mm, pitch 12 num and outside diameter of 38mm.
11 In uptight drill machine, the power is transmitted from electric motor to spindle with help of belt and pulley system. Select one: True False
Define Iron Stirrups
Describe the different types of hammers.
this problem is going to look very confusing because it really is.we have a block that is 6x6 that will have 2 holes the largest hole can be 1 1/2 inches with a 0.13 coefficient of friction, hole number 2 has no measure. To know what measurements can be chosen for hole 2, it must be taken into account that a gear will rotate by a shaft through hole to the crank. the crank length is 4 inches, shaft end 1/2 The rest of the details or measures we have to solve them that is, we have to obtain any measures that may make sense in the mechanism. For this to be clearer, the missing measurements either for the radius of the gears or any angle have to be calculated with our criteria. but they must be measurements that fit the size of the block (6x6) in the photo (45) are the questions of what to doFigure (7) is a past project that is very similar to this one, only that the two shafts will have a block joining them as seen in the photo (45) and some modifications.
Would the plank and the roller have the same acceleration why or why not?
Bolt material is 304 stainless steel. frame material is Aluminum. kindly assume all the other values and find the bolt size / diameter for bolt. write all formulas and explain the procedure. there are 2 bolts 1 on left and 1 on right.
Draw the free body diagrams for each part in the figures below:
What is the MMC of shaft "C"?
Refer to drawing 21A033, What is the wall thickness of the hub? All abbreviations are standard
9 MENG201 Mechanical workshop practice