A thick-walled pipe should be mounted in the space between a shaft and a wreath.... 1.A thick-walled pipe should be mounted in the space between an shaft and a wreath. The pipehas the inner radius a and the outer radius v2 a. The pipe fits perfectly on the shaft without gaps, but theradius to the edge of the wreath is ö smaller than the outer radius of the pipe, so the pipe must be pressedinto place. The material of the pipe has the elasticity module E and Poission constant v=1/2, the wreathand shaft can be considered rigid. Determine the tensions that occur at the inner and outer wall of the pipewhen pressed between the shaft and the wreath. course is "strength of materials"stel krans = stiff wreathrör = pipe%3Dstel axel = stiff shaftstel kransstel kransV2arör(stel axel)stel axelrörstel krans

Given-Data:- Inner Radius =aOuter Radius =2av=1/2 To-Find:- Tension

Answered: A thick-walled pipe should be mounted…

Engineering

Mechanical Engineering

A thick-walled pipe should be mounted in the space between a shaft and a wreath....

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Related questions

Q: APPLICATION OF HEAT LOSSES THROUGH BARE AND COVERED PIPES

A: Heat exchanger: A system which is used to transfer heat in between two types of fluid. One fluid…

Q: 155 About industrial piping: WHAT ARE THE DIFFERENCES BETWEEN THE FLOW CHARACTERISTICS BETWEEN…

A: The objective of the question is to understand the differences in flow characteristics between…

Q: Compare a orifice plate for low speed to a Pitot Static Tube.

A: Orifice plate is a flow rate measuring device used for restricting flow, for reducing pressure. It…

Q: Vasa ship sank during its maiden voyage on 10 August 1628. Why? Select one or more: O a. The ship…

A: To choose: The correct answer. Explanation: The Vasa ship shank because of the following reasons:…

Q: art One round metal branch duct will carry an airflow of 2,000 CFM with a static pressure drop- than…

A: Soln:- the static pressure drop for a 14" diameter metal duct branch carrying 2000 cfm would be…

Q: The vena contracta is the section where this minimum flow area occurs in a sudden contraction

Q: According to ASME B.31, what is the value of Y (reduction coefficient) in the formula below (wall…

A: The objective of the question is to find the value of the reduction coefficient (Y) for austenitic…

Q: (d) A vacuum system is used to evacuate (purge) refrigerant gas from an air-conditioning system.…

Q: Industrial Pipes Are pipes with screw connections not used when they have a large…

A: The question is asking whether the cost of threading is the primary reason why screw connections are…

Q: A circular duct is to measure 20.5 centimeters in diameter and 75 centimeterslong. It has a butt…

A: Given Data Circular diameter of the duct, D=20.5 cm The radius of the duct, r=d/2=20.5/2=10.25cm…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: At the lowest points of a pipe there should be drains and while at the highest points there should…

A: The objective of the question is to understand the reason behind the placement of drains at the…

Q: The difference between pressure relief valve and pressure reducing valve is

A: Difference between Pressure relief valve and pressure reducing valve

Q: A punch press has punches forty (40) circles that are 2 inches in diameter through medium carbon…

A: According to given conditionwe have the following equationPunching force=Area×Pressure forceHereArea…

Q: Example 11.2. We now wish to apply a sufficient pressure difference to the water flowing through the…

A: Given:To find:Value of Reynold's number, .

Q: Give solution asap , Handwritten required.

Q: Explain how the hyperbaric chamber helps to cure the bends

A: A hyperbaric chamber helps to cure the bends by the mean of a high-pressure chamber, by which a…

Q: What part of the circulating system has the maximum pressure drop across it? a. Drill pipe b.…

A: In a circulatory system, drilling fluid goes down through a hollow drilling tool consisting a nozzle…

Q: ##About industrial piping Design a simple and hypothetical piping system that connects equipment…

A: The objective of the question is to design a hypothetical piping system that connects various…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

100%

A thick-walled pipe should be mounted in the space between a shaft and a wreath....

1.
A thick-walled pipe should be mounted in the space between an shaft and a wreath. The pipe
has the inner radius a and the outer radius v2 a. The pipe fits perfectly on the shaft without gaps, but the
radius to the edge of the wreath is ö smaller than the outer radius of the pipe, so the pipe must be pressed
into place. The material of the pipe has the elasticity module E and Poission constant v=1/2, the wreath
and shaft can be considered rigid. Determine the tensions that occur at the inner and outer wall of the pipe
when pressed between the shaft and the wreath. course is "strength of materials"
stel krans = stiff wreath
rör = pipe
%3D
stel axel = stiff shaft
stel krans
stel krans
V2a
rör
(stel axel)
stel axel
rör
stel krans

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1,80 in. and the compressive force F is 3500 lb. The maximum allowable shear stress t^^, in the wall of the cylinder is 5500 psi. What is the minimum permissible thickness t„± of the cylinder wall? (Sec figure
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
Wires B and C are attached to a support at the left-hand end and to a pin-supported rigid bar at the right-hand end (see figure). Each wire has cross-sectional area A =0.03 in2 and modulus of elasticity E = 30 X 106 psi. When the bar is in a vertical position, the length of each wire is L = 80 in. However, before being attached to the bar, the length of wire B was 79.98 in. and wire C was 79.95 in. Find the tensile forces TBand Tc in the wires under the action of a force P = 700 lb acting at the upper end of the bar.
A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
A bar ABC of length L consists of two parts of equal lengths but different diameters. Segment AB has a diameter d 1 = 100 mm and segment BC has a diameter d 2 = 60 mm. Both segments have a length L / 2 = 0.6 m. A longitudinal hole of diameter d is drilled through segment AB in the middle of its length (distance L / 4 = 0.3 m). The bar is made of plastic with a modulus of elasticity. E = 4.0 GPa. Compressive loads P = 110 kN act at the ends of the bar. (a) If the shortening of the bar is limited to 8.0 mm, what is the maximum allowable diameter d max of the hole? (See figure part a.) (b) Now, if d max is set to d 2/2, at what distance b from the end C must the load P be applied to limit the shortening of the bar to 8.0 mm? (See Figure part b.) (C) Finally, if the loads P are applied at the ends and d max = d 2/2, what is the allowable length x of the hole if shortening is limited to 8.0 mm? (See figure part c.)
A bar ABC of length L consists of two parts of equal lengths but different diameters. Segment AB has diameter d1= 100 mm while segment BC has diameter dz = 60 mm. Both segments have length L/2 = 0.6 m. A longitudinal hole of diameter d is drilled through segment AB for one-half of its length (distance L/4= 0.3 m). The bar is made of plastic having modulus of elasticity E = 4.0 GPa. Compressive loads P= 110 kN act at the ends of the bar. If the shortening of the bar is limited to 8.0 mm, what is the maximum allowable diameter dmax (mm) of the hole? dmax d2 4. 2 (a)
6. Three wires are used to support the 150-lb force. The wires AB and AC are made of steel, and wire AD is made of copper. Assume that the three wires have constant cross-sectional area A = 0.0123 in?. For steel wire, a = 8 x 10 in/ (in°F ) and E = 29000 ksi and for copper wire, a = 9.6 x 10 in/ (in°F ) and E = 17000 ksi. Calculate the axial force exerted by the three wires if the temperature is raised by 80°F. Answer: Pu= 10 Ib, Pu= 136 Ib 40 in. 60 in. 45°. -45° 60 in. V150 Ib
The two pipes are made of the steel (E=210GPa, sy=420MPa)material and are connected as shown in Figure 3 and loaded by a force P at point C. The cross-sectional area of AC and CB are 600 mm2 and 900 mm2, respectively. The length of AC and CB are same a=b= (see attached file) If AC becomes plastic, determine the displacement of the step, the ultimate load of the stepped bar, draw a load-deflection diagram for the sectional area of AC and CB. a=b=9m
A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given Es= 2 x 105 N/mm and Ec= 1.2 x 105 N/mm2
A cylindrical steel pressure vessel has a 700 mm inner radius and 15 mm thick walls. Find the change in the inner radius when the vessel is pressurized to 1.5 MPa. Use E= 200 GPa and Poisson's ratio= 0.3 for steel.