A thermodynamic cycle with 0.1 kg of air has 3 processes as in the figure. Assume air as ideal gas. Consider constant specific heat approach (take the air properties at 300 K). P1=140 kPa, P2=420 kPa and V1=0.05 m³. 1-2: Constant volume process PA 2 2-3: Polytropic process with n=1 3-1: Constant pressure process 1 3 a) Find the temperature at State 3, in K. b) Calculate the specific work in the Processes 2-3 and 3-1, in kJ/kg. c) Calculate the heat transfer per unit mass in the Processes 2-3 and 3-1, in kJ/kg.

A thermodynamic cycle with 0.1 kg of air has 3 processes as in the figure. Assume air as ideal gas. Consider constant specific heat approach (take the air properties at 300 K). P1=140 kPa, P2=420 kPa and V1=0.05 m³. 1-2: Constant volume process PA 2 2-3: Polytropic process with n=1 3-1: Constant pressure process 1 3 a) Find the temperature at State 3, in K. b) Calculate the specific work in the Processes 2-3 and 3-1, in kJ/kg. c) Calculate the heat transfer per unit mass in the Processes 2-3 and 3-1, in kJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Basic Thermodynamics Question 422
Thermo
This is an Isothermal Compression of Ammonia [not an ideal gas] Ammonia in a piston-cylinder device initially at 700kPa, 303K undergoes a reversible isothermal compression process until the volume is reduced to 25% of the initial volume. a) Draw the process T-s and p-v-diagrams, relative to saturation lines. b) What is the heat and work per unit mass?
Given: P3 = 4 kPa, x3 = 0.6 , P4 = 4 kPa, T1 = 25 oC, T2 = 35 oC, mdot_steam = 25 kg/s. Find mdot_water (kg/s).mdot_water = _________ kg/s.
Q2 O of O points Q2:In a steam power plant operating at steady state is supplied to the high pressure turbine at 5 MPa and 400 °C. after expansion to 500 kPa the steam is reheated at constant pressure to the original temperature. The steam expands in in the low pressure turbine to an exhaust pressure of 10 kPa . Find 1- h:
In the piston-cylinder system shown in the figure, the piston rises up to (3) position. Choosing one of the 3 options given in the table, a) the pressure and temperature in positions (2, 3), b) Show the process change (1-2, 2-3) on the P-v diagram by drawing the saturation actions, c) find the total limit work and spring work, d) Find the heat transferred.
P.S write in detailed solution
Air as ideal gas in the closed system, find the change of entropy from the initial to the final state, in Btu/lb oR ( degree R ). T1 = 360 oF (degree F), P1 = 14.7 psia T2 = 540 oF (degree F), P2 = 58.8 psia
Q) A & B are rigid tanks. Tank A has volume of 1 m3 , contains steam with 4 MPa and 500 °C heated by external heat source with 130 kJ. The valve is open allowed to part of steam exit from the tank A to an evacuated and insulated tank B at constant temperature, then the valve is close when the final pressure in tank A reaches to 2 MPa and the mass reduce by 2/3. Determine the volume of tank B. A в
Read the question carefully and give me right solution according to the question
I need help with this thermo practove problem that I do not understand- thank you! 2 kg of air in a piston cylinder initially at P1=101 kPa, T1= 300 K undergoes a cyclemade up of three processes: 1-2 Isothermal compression until the volume is (1/15) of its original value.2-3 Constant Pressure heating3-1 Isentropic Expansion back to the initial state Assume air is an ideal gas with constant specific heats with the following values: Cpo=1.027kJ/kgK; Cvo= 0.740 kJ/kgK; R=0.287 kJ/kgK; ɣ=1.388 Fill out the processes table below. Calculate Processes 1-2, 2-3, and 3-1 clearly