A cycle works with one kg of air and is compressed through a polytropic process (pv12 = C) from state-1 at 120 kPa, 350K to state-2 of 600kPa, following a constant pressure cooling process to state-3, then constant temperature heating from state-3 to state-1. Represent the cycle on P-V diagram, find the temperature, pressure and volume at the end of each process of the cycle, and find also the net heat and work done.

A cycle works with one kg of air and is compressed through a polytropic process (pv12 = C) from state-1 at 120 kPa, 350K to state-2 of 600kPa, following a constant pressure cooling process to state-3, then constant temperature heating from state-3 to state-1. Represent the cycle on P-V diagram, find the temperature, pressure and volume at the end of each process of the cycle, and find also the net heat and work done.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The photo below is the refrigeration cycle of Ammonia, Im just confused on where h2 and Tsup=105 C came from? what kind of table usedand how it is used?
Two and one-half pounds of air actuate a cycle composed of the following processes; polytropic compression 1-2, with n = 1.5; constant pressure 2-3; constant volume 3-1. The known data are: p1 = 20psia, t1 = 100oF, QR = -1682 Btu. Sketch the p-V and T-S diagram. Compute and tabulate the p-V-T at all state points. Solve for the Wnet, QR, Efficiency and pm.
Thermodynamics question. Please explain every step(schematic, analysis, assumptions, etc.) Thanks
A cycle starts with an adiabatic compression of the air from state a with a volume V3 to state b with volume V1. At the end of the compression, heat is added (absorbed), resulting in an isobaric expansion to state c with volume V2 followed by an adiabatic expansion back to volume V3 at state d. Finally, heat is expelled, corresponding to an isochoric reduction completing the cycle and bringing air back to state a. Find the ratio between the initial and final temperatures for (1) the adiabatic compression, and (2) the adiabatic expansion in terms of the expansion ratio re = V3 /V2 and the compression ratio rc = V3 /V1..
The pressure of the air in a starting vessel is 40 bar and the temperature is 24°C. If a fire in the vicinity causes the temperature to rise to 65 °C. Neglect anyincrease in the volume of the vessel which is 5 liters. Please answer the following a. The thermodynamic process the problem representsb. the pressure, temperature, and volume after the processc. change in internal energy, change in enthalpy and change in entropyd. work nonflow and heat transferred
200Kg/min superheated steam at 40 bar and 350C enters a turbine through a 7.5cm ID pipe. It exits at 5bar as saturated steam through a 5cm ID pipe neglect the change in potential energy of the system. What is the temperature of the outlet saturated system? How much energy is transferred to or from the turbine?
Problem 22.3 Air is contained inside a simple piston cylinder device as shown in the figure. It expands from state 1 to state 2 according the process information shown below: State 1: P₁= 200 kPa; ₁ = 0.5 m³; T₁ = 300 K Process 1-2: Expansion process (see graph) where P = 50 kPa + (300 kPa/m³) State 2: P₂ = 350 kPa; ₂ = 1.0 m³ Determine: the work done on or by the air contained in the piston-cylinder device, in kJ (indicate direction, i.e., is the work done on or by the air?) Air P 350 kPa 200 kPa 1 0.5 1.0 Ans: d) 185 kJ <≤ Wnet] ≤ 200 kJ K
pls correct this given this is my last attempt thanks
Q2: A piston-cylinder system contains 1 kg of air at (V1, P1, T1). The air is heated at constant pressure process until the volume is doubled. Then the air is compressed according to the low (PV=C) until the piston regains its original position. Then the air is cooled at constant volume processes until the pressure reach to the original value. Assume (V1, P1), Draw the cycle on p-v diagram and calculate 1- Net work done 2- Net heat
Give me right solution.. Urgent please
A mechanical refrigerating system employing R-134a is operated under such conditions that theevaporator temperature is 4 oC and the temperature of the liquid at the refrigerant control is 42oC, determine the following:a) The properties of p, T, v, h and s for the state points A,B,C,D and E.b) The compressor displacement in L/s required per kilowatt of refrigerant capacity.c) The theoretical power in watts required per kilowatt of refrigerant capacity.d) The total heat rejected at the condenser in kilowatts per kilowatt of the refrigerantcapacity.e) The c.o.p of the cycle.
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. find Wnet, Ec, Ee and the ideal steam rate. Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. PLEASE USE THE STEAM TABLE PROVIDED: https://drive.google.com/drive/folders/15t3WMv7xSTHmwXWXp0X2ZV6aYWhXuRCS?usp=sharing