a) The truss structure in Figure Q4 is supported at A and D with downward vertical load F, acting at joint E and a downward vertical load Fa acting at joint C. The length of each truss member AB, BE, BC, CD and CF is 1.25 m. If F,=95 kN and F= 225 kN, determine the reaction force Ra and Ro at the supports A and D. Give your answers in kilonewtons (kN) to two decimal places. F1 F2 Figure Q4 b) For the truss structure in Figure Q4, determine the forces FAE. FAB and For acting in members AE, AB & CF and clearly state if each member is in compression or in tension. Give your answers in kilonewtons (kN) to two decimal places.

a) The truss structure in Figure Q4 is supported at A and D with downward vertical load F, acting at joint E and a downward vertical load Fa acting at joint C. The length of each truss member AB, BE, BC, CD and CF is 1.25 m. If F,=95 kN and F= 225 kN, determine the reaction force Ra and Ro at the supports A and D. Give your answers in kilonewtons (kN) to two decimal places. F1 F2 Figure Q4 b) For the truss structure in Figure Q4, determine the forces FAE. FAB and For acting in members AE, AB & CF and clearly state if each member is in compression or in tension. Give your answers in kilonewtons (kN) to two decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the FBD of block A, block B, and blocks A and B
1. Explain why, when temperature rises, the viscosity of a liquid reduces but that of a gas increases.
Direct stresses of 160N/mm2 tensile and 120 N/mm2 compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm2. a) What must be the magnitude of the shearing stresses on the two planes? b) What will be the maximum shearing stress at the point?
27/. a) The length and area of an aluminum rod are 63.99 cm and 1580 mm2 respectively. The rod is subjected to a stress of 252.25 N/mm2. Take the modulus of elasticity as 1860 MPa. Determine (i) load and strain in the circular rod (ii) diameter of the rod (iii) how much the rod is stretched. (2 Marks)
Two identical rods AB and BC form an L-shaped assembly. The assembly is pressed against a spring at D and released from the shown position. Knowing that the maximum angle of rotation in its subsequent motion is 60° with the horizontal (counterclockwise), Find the angle rod ABforms with the horizontal (degrees) whenthe angular velocity reaches 7 rads/sec. B 0.4 m 0,4 m ANSWER OPTIONS: A) 1.92 B) 6.73 C) 0 D) 5.46
Two point masses m and M are separated by a distance d. If the separation d remains fixed and the masses are increased to the values 3m and 3M respectively, how does the gravitational force between them change? A) The force will be three times as great. B It is impossible to determine without knowing the numerical values of m, M, and d. c) The force will be one-third as great. D The force will be nine times as great. E) The force will be one-ninth as great.
a.) determine average normal strain along AC after load has been applied. b.) determine average shear strain at A relative to x and y axis (gamma xy =) c.) determine average shear strain at point C relative to the x and y axes after deformation (gamma xy)
Please show you solution on a paper with complete unit of measures in every process. Will get a like.
Copra enters a dryer containing 60% water and 40% of solids leaves with 5% water and 95% solids. Find the weight of water removed based on each pound of original product. Answer: weight of water removed = 0.58 lb
39. During a heating process, the temperature of an object was increased from 35°C to 57 C. Determine the temperature rise in •R.
Need help solving this problem. Please provide clear and concise steps in neat handwriting.
Handwritten sol-please