(a) the load in VÀ (b) the load pf (e) the phase current (d) the phase voltage

Q: 1= 20/70° A E = 80/40⁰ V

A: W need to find out reactance for given current and voltage

Q: Calculate the value of RC in ohms. at VCC=18 V, IB=23 uA, and VC=7V and B=52

A: Given: Vcc=18 vIB=23 μAVC=7  and β=52 Calculation of RC in the given circuit :

Q: In case RL load, it is desired to get an average load voltage of 75 V. Determine the firing angle if…

A:

Q: Three alternating currents are represented by sine wave A. B and C as shown in Figure 6 below. (a)…

A:

Q: 30 40 IA 20 80 ww 16 40 VAB o Vo Figure 1

A:

Q: + 17V 14A+ R, 25V 0.41

A: Applying the nodal analysis at the node:

Q: Determine the output waveform for the network of figure below and calculate the output dc level.

A: Given: Let Vs=supply voltageVo=output voltagef=60 HzVoltage drop across diode=0.7V( Si…

Q: In an electrical installation, the active power is 500 kW and the power factor is 65% (lagging). How…

A:

Q: 10 22 62 82 20V 24V

A:

Q: Calculate the value of RB in ohms. at VCC=19 V, IB=27 uA, and VC=6V and B=65

A:

Q: ac = 250 mnH if

A: To find the equivalent inductance across the terminal a-b

Q: Sine-wave www 1.0 k generator 1.0 kHz 1.0 V Voltage across R1, VR Total current, I Voltage across L,…

A: In the given questions, we need to calculate the calculated and measured value of voltage across…

Q: What are the branch currents, 12 and 13? R₁ 4 kOhm V₁ 35 V R2 7.5 kOhm R 12.5 kOhm

A: Introduction Current divider rule: The current divider rule is an electrical principle that explains…

Q: E. Use this graphic for question 12 L1 L3 3mH 5mH L2 6mH

A: The solution is given below

Q: Determine Vo and In for the networks below. 15V Ip Si D1 Si D2 +V. 2.2k2 -5V

A: In case of multiple different question we are allowed to answer only the first question. Please…

Q: The inductive circuit has  ___________________ value of reactive power. a-Both positive and…

A:

Q: Vdc across the load is 110 V rms/ 1.0k 12.36V 24.73V 110V 55V

A: In this question,  We need to choose the correct options What is average DC voltage?

Q: Desian aproblem for wyr deltatransformations Determ the eauivalend resistance betwreen the terminals…

A:

Q: True or False Lenz' Law applies to all types of circuits, but in the case of dc circuits, all…

A: Given that Lenz' Law applies to all types of circuits, but in the case of dc circuits, all circuit…

Q: 12V ww +. +. 6Ω 15V 10V ww

A: There are 3 meshes in the circuit. Consider the 3 mesh currents as i1,i2,i3. Apply KVL to the…

Q: How many hours C O A) 0-24 O B) 0-48 O9 0-12 O D) 0-72 O E 02

A: UPSs generally feed their loads for 0-2 hours

Q: B- For the common-hase network of Figure below, determine a. Rc. b. Is and le e. Vac and Ver. Vo VI…

A: Given transistor is NPN transistor, as current leaves from the emitter terminal. First check whether…

Q: f=2000Hz Find the currents IAB, IBC, ICA, IaA, IbB, IcC, Iba, Icb, Iac.

A:

Q: Which one of the following voltage levels is not a standard level for residential loads Select one:…

A:

Q: What is the value of reactive power in a RL series circuit with a supply voltage of 220V, 60Hz and…

A:

Q: The following forward converter (for questions 8-12) has the following parameters. Vin=40V,…

A: Given Vin=40 VV0=10 VP0=50 WD=40%=0.4NP=16

Q: The total impedance in the polar form in ohm. The total current in polar form. The total power…

A:

Q: 6. Determine the peak and average power delivered to RL in figure. 2:1 RL 220 N 120 V rms alll lelll

A: In this question,   We need to determine the peak voltage Across the load and average power P?  We…

Q: 12 2 mA A Vo R4 R5 6 kQ 2 ko R1 R2 R3 8 mA 3 kQ 6 kQ 1 ka

A:

Q: A 10A current is lagging the voltage by 47° and a 12A current is lagging the voltage by 58°. What is…

A: Given:  10 A current lagging the voltage by 470 and 12 A current lagging the voltage by 580. We have…

Q: The voltmeters in the figure measure RMS voltages. If V1 = 13 V and V2 = 3.5V what is V3? R L VI V2

A:

Q: etermine the output waveform for the network of figure below and calculate the output dc leve Si D1…

A:

Q: How do you simulate a voltage source with 1000Hz 0-5V sqaure wave in ltspice?

A: LTspice, Multism, and MATLAB are important tools and libraries to analyze and design electrical…

Q: where can i find this component on multisim?

A: The component shown in the figure is a voltage source but its value depends on the value of the…

Q: A load consists of XL=20 Q and Xc=190 Q are connected in parallel across 120 Volt supply. The…

A: reactive power from element = voltage2reactance  here inductor absorbs reactive power whereas…

Q: Value of series impedance if inductance is 5mH , resistance is 4 ohm and frequency is 50 Hz.

A: Given values are =

Q: A load is connected to a 210 V, 50 Hz supply. If it has resistance of 30 02 and a capacitor of 0.25…

A: Supply voltage V = 210 V.Frequency f = 50 Hz.Resistance Capacitance

Q: In the Power tringle shown the reactive Power is equlen

A:

Q: Vs Ⓒ Q5: In the circuit shown below determine the input source voltage and its power factor. ZI o.o…

A: In this question we need to find the input voltage and its power factor.

Q: In order to prevent the reactive current drawn by the load in the circuit in the figure, it is…

A: To solve above problem, one should have basic idea about working of AC circuits. Above given circuit…

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.