A load consists of XL=20 Q and Xc=190 Q are connected in parallel across 120 Volt supply. The reactive power of the circuit is Reactive Power VAR

Q: From the given Ammeter diagram, the span is -- A. J0407 A a. -1 O b. 4 О с. 3 o d. -1 to 3

A: Given, Ammeter diagram

Q: Determine the DC currents (B. Ic and le) and de juncion voltages (VBE, VCE and Vca) mA. Ic ma, E mA…

A: In this question,  We need to determine the base current, collector current and emitter current?…

Q: R2 Q1 VCC R1

A:

Q: Calculate the value of RC in ohms. at VCC=18 V, IB=23 uA, and VC=7V and B=52

A: Given: Vcc=18 vIB=23 μAVC=7  and β=52 Calculation of RC in the given circuit :

Q: Vcc RB RC Q1 NPN +88 8 Volts VC

A:

Q: Find the compless power absorbed by the load.

A: This question is based on the concept of complex power drawn by a load. The load is connected across…

Q: In the following figure find sa Asa L turns ratio is A.0-7S A.07001

A: Solution                  Consider the  given diagram ,                                      The…

Q: An RL series circuit is connected to a 240 volt 60 hz line the capacitor has current of 1.25 amperes…

A:

Q: 1052 27V 27 mH 60 Hz 2.

A: Voltage and current  at different loads R-Load - There is no phase difference between voltage and…

Q: Determine the DC currents (1s. Ic and le) and dc junction voltages (VBE, VCE and Vca) In-Blank 1 mA,…

A: Given,  VBB = 3 VRB = 5 kΩRC = 232 ΩVcc = 18 VβDC = 65

Q: Vcc RB RC Q1 NPN +88 8 Volts VC

A:

Q: in a series Ri circuit voltage across the resistor is 100 V and the voltage across inductor is 50 v.…

A: Given, VR = 100 V , VL = 50 V, To calculate the power factor of the circuit.

Q: Millmans theory current thru 5ohm

A: Given: A circuit, To find: Current through 5 Ω resistance.

Q: What is the power factor (P.F) in this circuit? 80mH 60H2

A: This question belongs to circuit theory . It is based on the concept of calculation of power factor…

Q: How do you produce an AC source in Multisim and how you will put its voltage value in root means…

A: First of all , install Multisim software in your computer

Q: VCC R1

A:

Q: What is the capacitance of the capacitor in uf?

A:

Q: True or False Lenz' Law applies to all types of circuits, but in the case of dc circuits, all…

A: Given that Lenz' Law applies to all types of circuits, but in the case of dc circuits, all circuit…

Q: a capacitor and a resistor are connected in parellel to a 120 v 60 hz line the resistor has a…

A:

Q: A Resistor and an Inductor of negligible Resistance are connected in series to an AC Supply The PD…

A: When a resistor and an inductor are connected in series to an AC supply, the voltage across the…

Q: a resistor and and capacitor are connected in parallel to a 277 v 60 hz power source. the resistor…

A:

Q: What is the voltage between nodes A and B in each circuit in Figure 12–73?

A: The voltage across the capacitor can be calculated by using the capacitor reduction techniques and…

Q: hat will be the approximate value of the DC voltage component of the waveform at the output of block…

A:

Q: A load consists of XL=30 Q and Xc=120 Q are connected in parallel across 120 Volt supply. The…

A: Given, A load consists XL and Xc connected in parallel Inductive reactance, XL=j30 Ω Capacitive…

Q: Hw MANY MODES, LOOP, MEH IN THE FIEURE

A:

Q: What will be magnitude of the total circuit impedance of a series LR circuit excited by a 100 Hz ac…

A: If a circuit consists of series combination of a resistor of resistance R and an inductor of…

Q: an alternating current is given by i = 10sin 250. What is the time taken to generate two cycles of…

A: An AC current given by i = 10 sin(250t)  To find the time taken to generate two cycles of current

Q: When the input signal is AC voltage source reaches zero at every cycle, this will turn the thyristor…

A:

Q: • Show the voltage waveforms across each half of the secondary winding and across RL. • Find the…

A: In a full wave rectifier average output voltage is defined as, Vavg=2Vmπ Turns ratio and voltage in…

Q: Draw the waveforms of the voltage at the load (RL) end, the voltage at the R end, the voltage at the…

A: Draw the waveforms of the voltage at the load (RL) end, the voltage at the R end, the voltage at the…

Q: A 47-ohms load resistor is connected in series with a 10-uF capacitor. At what frequency will the…

A: In an AC-series R-C circuit, the impedance of C=10 μF capacitor is equal to R=47 Ω resistor. We need…

Q: A certain 2N5458 JFET has IDSS = 6.0 mA and VGS(off) = – 3.5 V. What is VGS at ID=3mA?

A: Given:-IDSS=6mA,VGSoff=-3.5vID=3mA

Q: Problem 13 Find is the resistance of a 29-m-long piece of 18-gauge copper wire having 1.024-mm…

A: 13.  The length of the 18-gauge copper wire is 29 meters.  The radius of the given wire is,…

Q: In general, the greater the absolute value of the impedance in a circuit: A. The greater the flow of…

A:

Q: A load consists of  XL=55  and XC=100  are connected in parallel across 155 Volt supply. The…

A:

Q: In series reactive power compensation, the Xc = 6.99 ohm and XL = 6.72 ohm, then the degree of…

A: In this we will find degree of compensation...

Q: A transformer with a primary voltage V = 15/15° V has a turns ratio of 1: 5. What is the secondary…

A: In this question , transformer primary voltage is given...We have to find transformer secondary…

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.