A tee section is made up of a 30mm x 150 mm flange and a 30 mm x 160mm web.  a) Determine the location of its neutral axis from the bottom of the top of the flange b) Determine its moment of inertia with respect to its centroidal x-axis

Q: The bar AB is supported by two rods- steel on the left and bronze on the right. If the bar is…

A:

Q: SOLVE the location of the Centroid from column ABC

A: Given data in question  Frame Point loads Span member lengths  Uniform columns   To find out…

Q: A wide flange section has the following properties. A = 6645 mm? by = 152.40 mm t - 10.80 mm d =…

A: Given data  A = 6645 mm2 bf = 152.40mm tf = 10.80mm d = 449.58mm tw = 7.62mm Fy = 250MPa

Q: The rigid bars shown are separated by a roller at C and pinned at A and D. A steel rod at at B helps…

A:

Q: Each steel member has a cross sectional area of 300 sqmm. Determine the force on member AC.…

A: Given- Area=300m2 The diagram is given below-

Q: eta = 30 degree T = 6kN   Find the magnitude of the resultant forces acting on the eyebolt.

A: Rx=Tsinθ+8cos45Ry=Tcosθ-8sin45Rx=6sin(30)+8cos45Ry=6cos(30)-8sin45Rx=8.65685kNRy=-0.4607

Q: Solve the angle of twist on a solid shaft, with 5cm radius and 50cm length, if the torque applied is…

A:

Q: Solve the forces for the following members. 10m 6m 4m 4m 5m 5m 5m 5m 200KN 200KN 400KN 400KN

A: To analyse the truss we should calculate the support reactions by taking summation of moments about…

Q: 100-lb.homogeneous plate is supported by a ball joint at A, a simple bearing at B, and a cable at C.…

A: Given:- W=100lb Vertical  force=120lb To find:- Force

Q: Determine the couple moment acting on the pipe shown .Segment AB is directed 30° below the x–y…

A: The couple moment acting on the pipe will be same as calculated about any point. So let us consider…

Q: 6 m 1 5 m ho = 2m ihD 4 m B

A:

Q: a T2 is secured to a wall by cables as shown. T1 = 58 N, T2 = 50 N, a = = 5 m, c = 6 m. ermine the…

A:

Q: 5- Replace the given forces by an equivalent resultant force and a couple moment at point P. [In…

A:

Q: Calculate the normal forces in the elements of the truss below. All the elements have the same EA.

A:

Q: 1. A 750 lb force is applied to the frame as shown.Determine the momen this force makes about point…

A: To find moment about point A

Q: 6 A 72 C W 2 T 30⁰ D B 12 A beam AB of length 1 and weight w supports a load W at its free end B and…

A:

Q: 3.From the steel shaft shown. Solve for the total angle of twist at the free end. Diameter = 50 mm G…

A:

Q: 8 kN 4 m

A:

Q: The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the horizontal…

A:

Q: find the global equilibrium of the truss.

A: The following  figure shows the Free Body Diagram of the truss.

Q: The block A in the figure supports a load W=1000 lb and is to be raised by forcing the wedge B under…

A: W=1000lb To find force P necessary to start the wedge under the block

Q: The wire BC has a diameter of 3.5 mm. Determine the vertical displacement of the handle at D if the…

A: Given data, Load P= 3000 N Diameter of wire BC= 3.5mm Modulus of Elasticity (E)=150 GPa =  1.5× 105…

Q: Problem 4. The Warren truss loaded as shown in the figure supported by a roller at C and a hinge at…

A:

Q: Determine the force in member AB, FE and CD using method of section. A |– 3 m →✦✦✦▬▬4 m —✦✦✦▬ 3 m →|…

A:

Q: A solid 30.0-mm-diameter steel [E = 290 GPa] shaft supports two pulleys as shown. Determine the…

A: To find deflection at C

Q: eering  If the tension in the gantry crane lifting cable is T = 14 kN.Define force T how as a…

A: Given:- T=14kN To find:- T

Q: F 650 N F = 500 N

A:

Q: Questions a/b c₁₂=c 200 10 E 5 0.291 m 20 40 289 10 0.312 200 0.323 0.328 10 1. 6.3 kNm torque is…

A: For given data:Torque = 6.3 kN-mLength of the shaft = 3mCross-sectional area, a= 5090 mm2Modulus of…

Q: 3m A 12 kN -3 m 8 kN B F -3 m C -3 m- E D 5m

A:

Q: Determine the resultant force at pins A, B, and C on the three-member frame.

A: FBD of the member AC

Q: A wide flange section has the following properties: bf =  200 mm tf =  7 mm d =  300 mm tw = 7…

A:

Q: 15 - In the plane truss system, the loading status of which is evident in the figure, the support…

A: A truss always has an axial forces in the member, and pin joint as an internal joint.  This pinned…

Q: The load on the bearing of a cast-iron bracket is 5 kN. The form of the section AB is given.…

A:

Q: A wide flange section has the following properties: bf= 240 mm tf = 8 mm d = 300 mm tw = 8 mm…

A: we have to calculate the radius of gyration in mm about the x-axis

Q: 4m 60⁰ 2kN C 60⁰ 2kN B 8m 30⁰ 2kN A

A: Cut the x-x plane as shown in below solution. Applying equilibrium equation in both x and y…

Q: Determine the allowable permissible Twisting moment, T (N-m) as shown in the figure: Tst ≤ 83 MPa…

A:

Pressure and Stress