A tacheometer with a stadia constant of 0.30m, and stadia interval factor of 100, was set up on the linebetween two points A and B. The following hair readings were observed.RODHAIR READINGS...POSITIONUPPERMIDDLELOWERRod held at A1.327m1.171m1.011mRod held at B2.004m1.867m1.707mIf the instrument height is 1.43m and it is set up on a point with elevation 14.72 m, determine theelevation of A.

middle reading is taken as straight reading is angle is not given.

Answered: A tacheometer with a stadia constant of…

A tacheometer with a stadia constant of 0.30m, and stadia interval factor of 100, was set up on the line between two points A and B. The following hair readings were observed.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

E2 Name:... Student no:.. Group: ...Date: 5. Questions 5.1 The sum of the clockwise moments and the sum of the anticlockwise moments differ by a small amount. What is this difference in Nm? Why do they differ? 5.2 This not a very accurate experiment. Name one improvement would you suggest for the apparatus to improve accuracy. 5.3. What do you understand by 'equilibrium' for the beam in this practical? 5.4 The meter rule could be fixed in place at the fulcrum and the whole apparatus, with your weights firmly attached, tilted to a constant angle 0 to the horizontal, (bench top). Equilibrium is established again. Would this action change the sum of the clockwise moments and the anticlockwise moments? Explain your answer. Further questions (submit on another sheet; stapled to this one) 1,0 x 2,0 rectangular steel plate of thickness 20 mm has forces of 50 N and 100 N acting on it as shown. Calculate the moment at point O, half way up one side. (density of steel = 8000 kg/ m'). 50 N 6. two…
A Civil Engineer used a 50m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial point and the end point was found to be 1.25 m. The 50 m tape is of standard length at a temperature of 10°C and a pull of 50 N. During measurement the temperature reading was 8°C and the tape was supported at both ends with an applied pull of 70 N. The cross-sectional area of the tape is 6 mm2 and the modulus of elasticity is 200 GPa. The tape has a mass of 0.075 kg/m. Coefficient of thermal expansion is 0.0000116 /°C.Determine the magnitude of the correction per tape length in meters due to temperature. Round off your answers to 4 decimal places. Determine the magnitude of the correction per tape length in meters due to pull. Round off your answers to 4 decimal places. Determine the magnitude of the correction per tape length in meters due to sag. Round off your answers to 4 decimal places. What is the…
1.5 Deflection checks are crucial in engineering and construction? why discuss briefly
Following observations were made to determine sensitivity of two bubble tubes A and B. Find which is more sensitive. Bubble tube A B Bubble reading (LHS) 13 08 15 06 Bubble reading (RHS) 05 12 03 14 Staff reading 1.681 1.767 1.635 1.788 Distance of staff from instrument = 100m
Do fast
Asaap
Lacking on mercury, an improvised barometer uses a liquid that weighs 0.735 times that of mercury. Assuming that the unit weight of air is constant 12 N/m^3, evaluate the approximate height of the mountain if the barometer readings are 600mm at the base and 850mm at the top of the mountain. specific gravity= 13.6
The term perception and reaction time (PRT) describes the period between the occurrence and the initiation of the physical reaction. True False
Samples of aluminum-alloy channels were tested for stiffness. The following frequency distribution was obtained. The distribution is assumed to be normal. stiffness frequency 2480 2440 23 35 2400 40 33 2360 2320 21 What is the approximate standard deviation of the population from which the samples were taken? O 19 O 23 O 37 O 51
Jisoo used a 40 meter steel tape in measuring an inclined distance on a gentle slope. The sloping distance was recorded to be 440 meters long. The difference in elevation between the initial point and the end point was found to be 32.49 m. The 40-meter tape is of standard length at a temperature of 20 °C and a pull of 34 N. During measurement, the temperature reading was 44 °C and the tape was supported throughout its length with an applied pull of 82 N. The cross-sectional area of the tape is 1.54 mm^2 and the modulus of elasticity is 200 GPa. The tape has a mass of 0.68 kg. Determine the corrected horizontal distance in meters. Round off to two decimal places.
A collimated beam of sodium light (λ = 589.3 nm) is incident normally on a Wollaston prism constructed from calcite with wedge angle of 15°, as shown in the figure. The angle of deviation between the two emerging beams equals [the refractive indices of calcite at this wavelength are n|| = 1.4864 and n₁ = 1.6584] OA 15% 15° OA
i need the answer quickly