A system has the frequency response 0.1 ja H(jw) = (1+10) (1 + 100) a) Sketch the Bode straight-line approximate gain plot (on the attached semilog paper): label the slope of any non-horizontal section(s) and label the dB level of any horizontal section(s); b) What type of filter does this represent? c) Using the table of op-amp circuits, sketch a circuit which will give this frequency response; you do NOT have to specify component (R and C) values.

A system has the frequency response 0.1 ja H(jw) = (1+10) (1 + 100) a) Sketch the Bode straight-line approximate gain plot (on the attached semilog paper): label the slope of any non-horizontal section(s) and label the dB level of any horizontal section(s); b) What type of filter does this represent? c) Using the table of op-amp circuits, sketch a circuit which will give this frequency response; you do NOT have to specify component (R and C) values.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Determine the mathematical model of: . a series RL circuit with an input voltage of Vs.
Circuit needed for this
Determine the mathematical model of: a parallel RC circuit with an input voltage of Vs.
1) In the amplifier of Figure 1, g--6.667 mS, Ip-0.5 mA, 2- -0.1 V and CL-31.83 pF. Neglect all other capacitances; Obtain the transfer function VeuVin (s). VDD 333M a) VHE M2 Vout Vin Vout VinoEM, CL Figure 1 b) Determine pole and zero frequencies of the transfer function. there タイCし c) Calculate the low frequency gain in dB. Construct the Bode plot of Voul Vin. d) 40 -20 2 34 10 20 10000 100000 100M 100 1000 Frequency (kHz) Magnitude (dB) 20
Feedback Control 1
= b) A three-stage amplifier system operated at T 25°C and 1 MHz bandwidth which is determined by an LC-tuned circuit. The first stage has a power gain of 10dB and an NF of 5dB, the second has a power gain of 20dB and NF=10dB, and the third stage has a power gain of 30dB and NF=10dB. The output load is 2000. The input noise is generated by a 20k resistor. Calculate: i) The noise voltage and power at the input and the output of this system assuming ideal noiseless amplifiers. ii) The overall noise figure for the system. iii) The actual output noise voltage and power.
(b) Block diagram of a system with unity feedback is illustrated as R(s) Y(s) K G(s) Figure Q3(b) and the transfer function is given as 50000 G(s) = s² + 150s + 5000 From the given block diagram and transfer function, sketch an approximate magnitude and phase of Bode Plot. Choose any value of K that you might think will simplify your sketching. There is no requirement of K value in this sketching process. The selection of Kis only necessary if you have a particular design requirement.
Q2] Design an op amp-based Non inverting low pass active filter with a cut off frequency of 500Hz and a passband gain of 1 using a 50nF capacitor. And Draw your circuit, labeling the component values and output voltage. And If the value of the feedback resistor in the filler is changed but the value of the resistor in the forward path is unchanged, what characteristic of the filter is changed?
Q2: Briefly discuss the operating principle of a Series Resonant Band-Pass Filter?
This circuit represents a small signal amplifier.If C1= 1.5 μF, C2= 0.43 µF Assuming the transistor has: ac current gain =100. dynamic resistance = 100, and Internal Capacitances C= 42 pF, Chc-4pF, C=1pF. 1- Calculate the critical frequencies for the low frequency response. 2- Calculate the critical frequencies for the high frequency response. 3- Write the general formula for voltage gain as function of frequency. 4- Sketch the Bode Plot for the voltage gain magnitude. 2 T mill 1kQ2 O 560 ΚΩ 4.3 ΚΩ C2 HA R1 2 2,7 ΚΩ
5. We would like to build a filter which implements the Bode approximate gain plot given below. a) What type of filter is this? b) Write an expression for the frequency response, H(jw), in Bode form; c) Write an expression for the transfer function, H(s), in pole-zero form; d) Use the table of op-amp circuits to sketch a circuit which has this frequency response. You do NOT have to specify component (R and C) values. OdB 10 104 105 106