A swivel bridge is bought into the desired position by means of a double–acting cylinder. The piston rod of a double–acting cylinder is to extend when a push button switch is actuated. The cylinder is to remain extended until a second switch is actuated and only if the first switch has been released

Q: A motor with a 3-inch drive pulley is belt-coupled to an equipment that operates at 900 rpm and has…

A:

Q: When servicing transfer cases, all of the following are correct, except

A: When servicing transfer cases, all of the following are correct, except a. it must be supported on a…

Q: State four advantages of a pre-engaged starter when compared with an inertia type.

A:

Q: Find the forward and return velocities of an offset slider crank mechanism rotating at 1500 rpm…

A:

Q: 1Y1 1V2 182 1A 181 1V14 1Y2 2Y1 2A 2V2 2V14 251 ZM 252 After exchanging the adjustable one-way flow…

A: The effect of the mistake on the operation of the control circuit.

Q: Find the toggle position and determine the transmission angle of this system. Please use the…

A: Given:To find:Toggle position and transmission angle.

Q: (M011) 1. Find the degrees of freedom of the following mechanisms. a. J Cam contact P Pin in slot

A:

Q: Create 2 kinematic diagram of a mechanism that can draw a square (with driving linkage and crank)

A: It is asked to draw kinematic diagram to plot a square

Q: QUESTION 3 Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and…

A: input speed, N1 = 1750 rpm output speed, N2 = 725 rpm linear velocity, v = 4000 ft/min

Q: Circuit Design - aircraft system application Draw the circuit of the flap and aileron actuation…

A: Ailerons:An aileron is used to control the roll of an aircraft. They are installed on the trailing…

Q: Match the following terms with the definitions. Damping Bandwidth End point Home position…

A: Solution:   The following are correctly matched below:

Q: motor, operating clockwise is coupled through a belt drive to rotate an industrial exhaust fan at…

A:

Q: how does the baulk ringblock the sleeve from engaging with the dog teeth on the gear before…

A: To synchronize the gears, baulk ring synchromesh system is used very widely. The name is derived…

Q: Select the type of this mechanism below: L2 L3 A 03 C LA O Crank-rocker O Triple rocker O…

A: In the Slider-crank mechanism, the mechanical parts designed to convert linear motion to rotary…

Q: 4.(a) fixed displacement motor (b) Hydraulic operated check valve (c) Directional control valve for…

A:

Q: 1750 rpm motor has a 3” pitch diameter drive pulley. It is driving a 9” pitch diameter pulley. What…

A: GivenSpeed of driver pulley ω1=1750rpmdia=3''dia of driving pulley=9''

Q: Circuit Design - aircraft system application Draw the circuit of the flap and aileron actuation…

A: Ailerons:An aileron is used to control the roll of an aircraft. They are installed on the trailing…

Q: B L2 L3 A 03 L4

A: Draw the schematic diagram for the above problem.

Q: the roller track is to be swivelled by means of a double-acting cylinder. the signals to extend and…

A: The system described is a typical pneumatic or hydraulic system where a double-acting cylinder is…

Q: Draw a 3 kinematic diagram of a mechanism that can draw a square including its driving linkage AND…

A: It is asked to draw kinematic diagram to plot a square

Q: A local farm uses a tractor as a prime-mover for carrying out farm operations such as: plowing,…

A: Draw the given diagram.

Q: The Mobility of a four bar change point mechanism is O 1 O 3 O 4

A: Consider : - The number of links is l. The number of lower pair is j. The number of higher pair is…

Q: The speed of a moving coil motor (MCM) is varied by O changing the DC voltage applied to the…

A: