can you write the angles and loops for the first mechanism like they did in the second one

Q: inverse kinematics of

A: introduction: we have to find out inverse kinematic

Q: Find the toggle and limit positions.

A:

Q: Question No. 1: A pair of bolt cutters is shown in Figure 1.0. Draw a kinematic diagram of the…

A: Solution:

Q: Write

A: The spindle speed of machine is, N = 1800 rpm. The feed rate is, f = 3 mm/min. The depth of cut is,…

Q: Graphically position the links for the compressor linkage in the configuration shown in Figure P4.5.…

A:

Q: Q6 Figure Q6 shows the masses of the boxes are ma = x kg and mp = y kg. The coefficient of static…

A:

Q: 4. Design 4-bit left and right rotators. Sketch a schematic of your design.

A:

Q: Find the maximum and minimum transmission angles over its range of motion.

A:

Q: What is the magnitude of the moment done by the force about the "z-axis" in the following figure. 4…

A: The position vector at which force is acting is determined as, OA→=-3i^-7j^+4k^

Q: Write the sequential procedure and CNC code for making the simple step turning operation for making…

A: Please find the answer below

Q: By finding all the sudden rotation centers of the mechanism given in Figure 1 below Explain by…

A: The sudden rotation center is known as the Instantaneous center. The total number of instantaneous…

Q: Write the sequential procedure and CNC code for making the simple step turning operation for naking…

A: CNC Codes: There are two types of codes used in CNC programming G Codes M Codes

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: Write and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as;…

A:

Q: The 6-DOF robot shown below represents what kind of kinematic chain – open o [ Note: Assume the base…

A: kinematic chainA system of rigid bodies connected together by joints. 1. A chain is called closed if…

Q: 1)Design a crank sharper quick return mechanism for time ratio of 1:2.5   2)Design a fourbar crank…

A: 2) four bar crank rocker for 120degree of output motion with time ratio of 1:1.2

Q: In the drawing below, which feature control frame controls the form of datum feature A? L.006 A B 3…

A: Feature control frame is used to show or describe the condition and tolerances used in designing of…

Q: Get the degree of freedom of the following mechanism. Pin in Siot

A: Degree of freedom for the following mechanism

Q: - following mecha

A:

Q: Put in ternary links without changing its mobility. Sketch linkage.

A: Given drawing of the ternary link mechanism or  four bar mechanism

Q: Ball B (10 kg) is on a rod on which a torque of M = (2t² + 4) Nm where t is in seconds. Fin the…

A:

Q: Write the G code and M code for the design attached, as well as state the meaning of each codes used…

A: The machine spindle speed is, N = 1800 rpm. The rate of feed in machine is, f = 3 mm/min. The given…

Q: The reversing motor,which is controlled by two power relays,can be rotated in both directions as…

A: The ladder and Relay diagram for the given system is shown below which can be used to control the…

Q: 14-23. Water flows through the 400-mm-diameter delivery pipe at 2 m/s. Each of the four…

A:

Q: C A A 3 B 3 A B O2 2 4 4 02 Assume rolling contact Assume rolling contact 2.

A:

Q: Can someone draw grashof's mechanism: Crank-rocker Mechanism in ENGINEERING DRAWING FORMAT basing…

A: The crank-rocker mechanism,

Q: Produce a 3D solid model of the Guard casing and test boss and produce an assembly of the two parts…

A: Given Guard casing Test boss To find Parts Assembly

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Design a kinematic machine that includes at least two of the following systems: gears, belts/chains,…

A: Design the kinematic machine with gear ad belt.

Q: As mentioned in the below given DCV, extend stroke respectively. and Lare the positions are used for…

A:

Q: The figure below represents a Whitworth quick-return mechanism which is used in shapers. It is…

A:

Q: Draw the kinematic diagrams of the following mechanisms and compute the number of Degrees of Freedom…

A: Draw the kinematic diagrams of the following mechanisms.Compute the number of Degrees of Freedom…

Q: Get a kinematic diagram (schematic view) equivalent to the following mechanism and its degree of…

A: kinematic diagram,

Q: R6 R12 29 R8 25 80 105

A: Given: The depth value is, z=5 mm. Assumptions: Spindle speed is (300) in (rpm) is, S300. Feed…

Q: ong cable is wrapped around the spool shown and released from rest. What is downward acceleration of…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.