A swimming pool is filled with 2 m of water. Its bottom is square and measures 4 m on a side. Two opposite sides are vertical; one end is at 45° and the other makes an angle of 60° with the horizontal. Calculate the force of the water on (a) the bottom, (b) a vertical side, (c) the 45° end, and (d) the 60° end. Use the hydrostatic equation.

A swimming pool is filled with 2 m of water. Its bottom is square and measures 4 m on a side. Two opposite sides are vertical; one end is at 45° and the other makes an angle of 60° with the horizontal. Calculate the force of the water on (a) the bottom, (b) a vertical side, (c) the 45° end, and (d) the 60° end. Use the hydrostatic equation.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1 m A rectangular gate 1.6 m wide is used as a partition as shown. One side has linseed oil filled…

A: Given data in question Depth Specific gravity Width of gate To find out Pressure on right side of…

Q: intérnal force in member BF by method of joints. Determine if the nember is in tension or…

A: To find force in member BF

Q: Water flows into the atmosphere from a nozzle and strikes a vertical plate as shown in the figure…

A: Diameter of pipe (D1) = 0.3m Area of pipe (A1) = Πd2/4 = 0.0706 m2 Diameter of the nozzle (D2) =…

Q: Calculate the depth of the center of pressure for vertical rectangular plate having a height h =…

Q: Water is flowing into and discharging from a vertical pipe U-section as shown in Figure. At flange…

Q: Problem 15.120 The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with…

Q: a vertical wall separates two different fluids in an open tank. the right side of the tank contains…

A: A tank have been given in the which has been separated by a wall and at the bottom of wall hinged…

Q: a rectangular gate of width "a", length "b" and inclined at an angle "A", with water on one side is…

A: a) location of centre of gate from water surface along plane of gate from water surface =xy'+b2…

Q: 114 liters/second of water passes through the 30-degree elbow shaped on the side. The mass (M) of…

A: One of the crucial standards utilized in the examination of uniform stream is known as the…

Q: force acting on the gate in cer of gravity to the center

A: Given:- width=1.60m h=2.0m inclined=8 degree To find:- force acting on gate force needed to open…

Q: 36 " chinge Linseed Oil А (SG = 0.938) Castor Oil 32 feet (SG = 0.96) 7 feet 11ater В

Q: The masonry dam shown in the figure is subjected to water pressure at upstream side. It is built on…

A: Find: Minimum width at the base to develop no tension

Q: 1. The tank in figure is 3 m wide into the paper. Neglecting atmospher compute the hydrostatic (a)…

Q: A cylindrical tank 4.6 meters in diameter and 4 m long, with its axis horizontal is half filled with…

A: Centroid of pressure diagram will be the location of force.

Q: A water tank has a right-triangular panel near the bottom, as in Figure 2. Omitting Pa, find and…

Q: horizontally along its length just before any liquid

A: Data given Height of tank, H=10.61m length of tank, L=8.66m width of tank, W=3.66m Depth, D=7.56m…

Q: The sluice gate is a circular arc of radius 5m and angle B=60°. The water level behind the gate…

A: The radius of the circular arc, R= 5 mAngle, Length of the gate, L= 3 mTo find:The vertical…

Q: Water is flowing at 0.020 m'/s at steady-state through a reducing 90-degree bend in the horizontal…

A: given data Q=0.02m3/secd1=0.05m and…

Q: The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to…

Q: swimming pool has a width of 4 m and a side profile as shown. Determine the resultant force.…

Q: A curved surface was submerged in water as shown. Calculate the horizontal component of the…

Q: In a tunnel, there is a vertical circular gate with 8 meters in diameter that is submerged in oil…

A: Given data Depth of Oil = 12m Diameter of gate (d) = 8m Air pressure (Pair) = 40 KPa Specific…

Q: Determine the magnitude of the hydrostatic force, its direction and location. 1. A tank is filled…

Q: 45. A 1-meter-diameter cylinder is connected to a 2-meter-wide rectangular gate as shown. The gate…

A: y = 4 m d = 1 m h = 2.5m

Q: Problem 2. In reference to the figure, gate XY is 1.20m wide and 1.40m long., If the liquid in the…

A: To determine total hydrostatic force "F" acting on the gate its line of action "h₂" vertically from…

Q: 2. Points A and B are 5km apart along a new 60 cm cast iron pipe carrying water. A is 9 m higher…

Q: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two…

Q: An L-shape gate AOB weighing 20 kN at its center of gravity G, 0.6 m above the bottom and 0.5 m from…

A: To determine the height of water so that no reaction is developed at the stop (B). Given, Weight…

Q: Consider a 12-inch diameter steel pipe (ks = E = 1.5 x 10* ft) which has water flowing under…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Consider a 7-m-long. 7-m-wide, and 3-m-high swimming pool that is filled with water to the rim. a)…

A: Given: Length of pool, l = 7 m Width of pool, w = 7 m Height of pool, h = 3 m

Q: Calculate the total hydrostatic force and the location of the center of pressure (y,) acting on the…

Q: The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of…

Q: vertically into a body of water with open end down and floats with a 1300 N block of concrete (SG =…

A: D=350mm h=1.8m

Q: ) Water flows in a rectangular channel of 5 m wide as shown in figure below. Calculate a) the force…

Q: .80 Water (p = 62.4 lbm/ft³) flows from the large orifice at the ottom of the tank as shown. Assume…

A: To find pressure difference at point A and B

Q: In the swimming pool shown below, determine the resultant hydrostatic force and locate the center of…

A: To determine the resultant hydrostatic force and location of center of pressure on surface AB.…

Q: Water flows through a horizontal pipe with a cross-sectional area of 5m^2 at a speed of 6L/sec. With…

Q: diameter on the liquid surface. a. Compute for the value of eccentricity if the top of the gate is…

Q: component of the total hydrostatic

A: length of gate = 3.11m a =7.8m b= 2.4m r=3m we need to find the vertical component of force

Q: .A cylindrical log having a diameter of 2m and 6m long is used as a gate to control the flow of…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

1. A swimming pool is filled with 2 m of water. Its
bottom is square and measures 4 m on a side.
Two opposite sides are vertical; one end is at 45°
and the other makes an angle of 60° with the
horizontal. Calculate the force of the water on
(a) the bottom, (b) a vertical side, (c) the 45°
end, and (d) the 60° end. Use the hydrostatic
equation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An open rectangular tank 2.2m in length contains 16m^3 of gasoling (sg=0.70) and 23m^3 of water. The fluid is arranged in two stable layers. Determine the total hydrostatic force(kN) on one of the two smaller vertical sides of the the tank.
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.
A curved surface was submerged in water as shown. Calculate the vertical component of the hydrostatic force on the curved surface. The system is 2m wide into the paper. 5m 60° r = 2m
... 4m 2m Hinge Water 50cm 420cm 30cm B.
Question 4. The L-shaped cap in the figure is hinged from point A. Neglecting the weight of the lid, a) Before opening the lid counterclockwise, determine the maximum water height H in symbols. b) If w=4 m (width of the cover perpendicular to the plane of the paper), B=5.77 m and d=6 m, determine the numerical value of H. C) Find the horizontal and vertical components of the hydrostatic force and the resultant force direction with the values given in b B articulation A H
3m W.S 3 10 6m 6m 10 W.S Sm 6m 6m draln 1. A section of a gravity masonry dam is shown in the figure water is flush at the top of the dam upstream and 5m from the ground downstream. Assume hydrostatic uplift to vary uniformly from full hydrostatic pressure from the heel to zero at the drain density of water is 1000kg/m^3. The specific gravity of concrete is 2.4. Determine: a. The location of the resultant force b. Factor of safety against sliding if coefficient of friction is 0.75 c. Factor of safety against overturning d. Stress at the heel and the toe e. Unit horizontal shearing stress at the base f. Factor of safety against overturning neglecting uplift
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. a. The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c. The hydrostatic force due to water. d. The net hydrostatic force acting on the gate Fnet
Water at 20°C flows through a 11.5-cm-diameter pipe that has a 180° vertical bend, as in the figure. The total length of pipe between flanges 1 and 2 is 75 cm. When the weight flow rate is 230 N/s, p1 = 165 kPa and p2 = 134 kPa. Neglect pipe weight. Determine the magnitude of the horizontal force balance that the flanges must withstand for the flow. The magnitude of the horizontal force F= -106.958 N
A tank 13 ft deep and 5 ft wide is layered with 6 ft of oil (y = 50.0 lbf/ft3), 5 ft of water, and 2 ft of mercury (y = 846 lbf/ft3). Compute (a) the total hydrostatic force and (b) the resultant center of pressure of the fluid on the right-hand side of the tank.
please answer with a neat solution and provide all answersA curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w = 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m.Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer.Determine the vertical component of the hydrostatic force (in N) acting on the gate, indicate the direction by putting an U for upward and D for downward after your numerical answerDetermine the magnitude (in N) of the hydrostatic force acting on the gateWhat angle (in degrees) does the hydrostatic force F make with horizontal?