A student is asked to standardize a solution of potassium hydroxide. He weighs out 1.08 g potassium hydrogen phthalate (KHCgH404, treat this as a monoprotic acid). It requires 29.9 mL of potassium hydroxide to reach the endpoint. A. What is the molarity of the potassium hydroxide solution? This potassium hydroxide solution is then used to titrate an unknown solution of hydroiodic acid. B. If 23.4 mL of the potassium hydroxide solution is required to neutralize 17.4 mL of hydroiodic acid, what is the molarity of the hydroiodic acid solution? M M

A student is asked to standardize a solution of potassium hydroxide. He weighs out 1.08 g potassium hydrogen phthalate (KHCgH404, treat this as a monoprotic acid). It requires 29.9 mL of potassium hydroxide to reach the endpoint. A. What is the molarity of the potassium hydroxide solution? This potassium hydroxide solution is then used to titrate an unknown solution of hydroiodic acid. B. If 23.4 mL of the potassium hydroxide solution is required to neutralize 17.4 mL of hydroiodic acid, what is the molarity of the hydroiodic acid solution? M M

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A 15.00mL sample of ammonium hydroxide (0.980g/mL) is titrated with 31.25mL of0.500M HCl. Find the molarity and mass percent of the ammonium hydroxidesolution. Be sure to start with a balanced equation.
A 3 mL sample of concentrated nitric acid solution is diluted to 150 mL. A 15 mL sample of the diluted solution requires 29.43 mL of a 0.0171 molar solution of potassium hydroxide to be titrated to the equivalence point. Determine the mol per liter of the original nitric acid solution.
Please answer the question! Find the molarity and mass percent of ammonium hydroxide solutions. Thanks!
||| O ACIDS AND BASES Calculating percent dissociation of a weak... A student prepares a 0.41 mm aqueous solution of acetic acid (CH3cO₂H). Calculate the fraction of acetic acid that is in the dissociated form in his solution. Express your answer as a percentage. You will probably find some useful data in the ALEKS Data resource. Round your answer to 2 significant digits. % 0 x10 0/3 X
% C in a sample can be obtained using indirect titration. All carbon compounds are converted to CO2 gas. The CO2 gas is then reacted with excess Ba(OH)2. See reaction below. CO2(g) + Ba(OH)2(aq) -> BaCO3(s) + H2O The excess Ba(OH)2 is reacted with HCl. What type of titration is involved in this analysis ? a. acid- base b. complexometric c. precipitation d. redox
QUESTION 5 Consider the titration of 17.7 mL of 0.211 M HNO3 with 0.130 M NaOH solution. What volume (in L) of NaOH is required to reach the equivalence point in the titration? Give your answer in numerical form (NOT exponential notation) using the correct number of significant figures. Lavide jon.
You have 500mM stock of Tris base. What volume of this stock solution should be added to water to prepare 2L of 5.5mM Tris base?
This is a question for a lab about the standardization of an acid and base. In the lab, we used the weight of KHP to calculate the moles of NaOH and the molarity of NaOH( KHP and NaOH have a 1;1 mole ratio in the reaction). Then, we used the molarity of NaOH to calculate the molarity of HCl. If you recorded the weight of the KHP incorrectly, the value was too low, how would this effect the molarity of the HCl you calculate? I think the calculated molarity of HCl would be lower than what it should be. I just want to double check
1
Q 29.
Calculate the concentration of an HCl solution if 100.0 mL of the HCI required 33.00 mL of 0.2000 M Mg(OH)₂ to reach the titration endpoint. Mg(OH)2 + 2 HCl → 2 H₂O + MgCl₂ There is enough information to calculate the moles of base but not the moles of acid. mol b. 0.1320 i. OH-1 p. CO3² W. PO4³ a. 0.1000 h. CaCO3(s) o. H₂PO4-¹ v. H₂CO3 bb. 3.300 x 10-² hh. 2.16 x 10-6 L)(- mol Mg(OH)3)(- mol HCI c. HX j. H30+1 q. HCO3-¹ x. HCzH3Oz dd. 2 jj. 0.2000 d. Al+3 k. SO4² r. H₂S CC. 3 ii. 1.60 x 10-5 e. CO₂ 1. Mg+2 S. HS-1 y. C₂H30₂-1 ee. 1 = mol HCI mol Mg(OH)₂ M HCI f. CaF2(aq) m. C-1 t. S-2 z. 1 x 10-14 ff. 0.099536 kk. 6.600 x 10-³ g. HF(aq) n. HPO 2 u. H₂O(lig) mol Mg(OH)3 aa. 1.32 x 102 gg. 3.95 x 10-3 mol HCI
Can you help me answer this questions!