A student extends then releases a mass attached to a spring. A graph of the mass's displacement over time is shown below. Displacement (cm) 5- 4- 3 2+ 1- -2+ -3 -4- -5- 1 2 3 4 What is the period of the oscillation? 5 6 7 Time (s) 8

A student extends then releases a mass attached to a spring. A graph of the mass's displacement over time is shown below. Displacement (cm) 5- 4- 3 2+ 1- -2+ -3 -4- -5- 1 2 3 4 What is the period of the oscillation? 5 6 7 Time (s) 8

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The damped frequency of oscillation of an open loop underdamped system = 12rad/sec The magnitude of the real part of the underdamped system = 16 Determine the natural frequency (Answer to 0 decimal places)
Given the vibrating system below: K4 Y(t) =Ysin30t where for = 30 and Y=20mm Find the following K1 K2 m C3 H C2 C1 C5 C4 1. Frequency Ratio 2. Displacement Transmissibility Ratio 3. Absolute displacement of the mass 4. Type of Damping 5. Equation of motion x(t). Assume Initial conditions for displacement and velocity 6. Graph 2 cycles of the vibrating system. You can use third party app for this. M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2=40 Ns/m C3= 35Ns/m C4= 15 Ns/m C5= 10 Ns/m
a) A two-degree-of-freedom coupled pendulum model is shown in Figure Q1a. The parameters of the model are: k=100 N/m; m=10 kg and L=1 m. The equations of motion of the system are given below. J₁ä + (mgL + kĽ² ) 8₁ - kľ² 0₁₂ = 0 J₁₂+(mgL+kĽ²)₂-kĽ² 0₁ = 0 i) Calculate the natural frequencies. ii) Draw the mode shapes. m Figure Q1a. b) In the above system discuss the implications of the following changes in coupling stiffness. i) k is reduced considerably to 0.1 N/m. ii) k is increased considerably to 1x105 N/m. c) Draw a schematic of modal test arrangement of a beam using instrumented impact hammer. d) Why is it necessary to measure force in a modal test?
The 10.8-kg rod is released from rest when 0=0° [position 1]. Knowing that OA=1.35 m, OB=1.8 m. The spring (K=20 N/m}) is unstretched when 0=0°. It reached position (2) when 0=90°. OB В OA Kinetic energy when 0=0° polar moment of inertia at O (kg.m2) work done by weight is (Joules) extension of spring when 0=90°. (m) angular velocity when 0=90° (rad/s)
A weight is attached to a spring and reaches its equilibrium position (x = 0). It is then set in motion resulting in a displacement of x = 6 cos t, where x is measured in centimeters and t is measured in seconds. See the figure shown to the right. Answer parts (a) and (b). (b) What is the spring's velocity when t = 0? cm/sec (Type an integer or decimal rounded to one decimal place as needed.) ī www winn - 6 0 6 Equilibrium position at x = 0
1) Is it possible to prescribe the velocity v0, so that the pendulum keeps rotating with alpha = pi/2 Explain clearly why? Given: L, g, and m. 2) After transient motion, the pendulum settles at steady state rotation atalpha = pi/3. Find the initial velocity v0. Given: L, g, m, sin(pi/3) = (squareroot(3)/2), cos(pi/3) = (1/2). [Hint: Use the conservation of energy and the 2nd Newton’s law.]
Three engineers are independently estimating the spring constant of a spring, using the linear model specified by Hooke’s law. Engineer A measures the length of the spring under loads of 0, 1, 2, 4, and 6 lb, for a total of five measurements. Engineer B uses the same loads, but repeats the experiment twice, for a total of 10 independent measurements. Engineer C uses loads of 0, 2, 4, 8, and 12 lb, measuring once for each load. The engineers all use the same measurement apparatus and procedure. Each engineer computes a 95% confidence interval for the spring constant. If the width of the interval of engineer A is divided by the width of the interval of engineer B, the quotient will be approximately _____. Numeric Response
Please answer quick you are in a bumper car with a total mass of 200.0kg your friend is also in a bumper car with a total mass of 200.0kg.You are moving to the right at 1.00m/s. Your friend is moving to the left at 0.500m/s. Your car hits a spot on your friends car that has no bumper. Your bumper acts as a spring with a spring constant of 2.00x10^4N/m. Determine the velocity of your car when the bumper has raced a maximum compression of 0.0700m.Assume friction is negligible.
A spring with mass 1 kg is attached to one side of a spring with spring constant k = 12 kg/sec2. The other end of the spring is connected to the side of a steel beam so that the spring may oscillate in the horizontal direction. Suppose that friction is proportional to velocity with constant of proportionality f = 7 kg/sec. Write a differential equation for y(t), the position of the mass at time t, with the initial conditions y(0) = 0 and y(0) =1 m/sec. Solve your resulting IVP.
A force of 60 N stretches the spring 30 cm. A body of mass of 4 kg is hung from the spring. The spring is then pulled down 10 cm and released. a) Find the period of Oscillations, b) Find the direction and magnitude of oscillation if the mass is 5 cm from equilibrium. c) What is the shortest time to go to equilibrium?
Two particle of respective masses mi = 4m and m2 = 3m are attached to two spring of respective spring constants k and 3k as shown in the adjacent figure. k ļ 4m 3k 3m a) Write down the Lagrangian of the system. b) Obtain Lagrange equations for each coordinate. c) Calculate the normal frequencies of the coupled oscillations. Deduce which frequency correspond to the symmetric and non-symmetric modes. d) Find the normal modes (eigenvectors) associated with the normal frequencies. e) Deduce a general solution for x1(t) and x2(1). f) Obtain a normal coordinate for each of the normal frequencies.
A single degree-of-freedom linear elastic structure was subjected to a series of harmonic excitations, one at a time. The excitations had the same forcing magnitude but different forcing frequency. Forcing frequencies and observed peak steady-state displacements are shown in the graph below. Find the natural period and damping ratio of the structure. Displacement (mm) 60 50 40 30 20 10 0 0 1 2 . 3 4 Forcing frequency, f [Hz] 5 4. 6 7