A straight pipe has a diameter of 25 mm, a roughness height of 0.1 mm, and is inclined upward at an angle of 10°. The pipe transports water at 20° C Part A If the pressure at a given section of the pipe is to be maintained at 550 kPa, determine the pressure at a section 100 m downstream for flows of 2 L/min. Express your answer to three significant figures and include appropriate units. μA ? 715 kPa Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining ▾ Part B If the pressure at a given section of the pipe is to be maintained at 550 kPa. determine the pressure at a section 100 m downstream for flows of 20 L/min Express your answer to three significant figures and include appropriate units. μA ? 674 kPa Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining

A straight pipe has a diameter of 25 mm, a roughness height of 0.1 mm, and is inclined upward at an angle of 10°. The pipe transports water at 20° C Part A If the pressure at a given section of the pipe is to be maintained at 550 kPa, determine the pressure at a section 100 m downstream for flows of 2 L/min. Express your answer to three significant figures and include appropriate units. μA ? 715 kPa Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining ▾ Part B If the pressure at a given section of the pipe is to be maintained at 550 kPa. determine the pressure at a section 100 m downstream for flows of 20 L/min Express your answer to three significant figures and include appropriate units. μA ? 674 kPa Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: local losses at points A, B, C, and D for pipes in series shown in Figure 1. Assun fully turbulent…

A: According to given data .

Q: A fluid with unit weight of 6.67 kN/m² flows, from a 0.3 m diameter pipe inside of which the…

A: The unit weight is γ=6.67 kN/m3. The pressures are P1=300 kPa, and P2=120 kPa. Apply the continuity…

Q: QUESTION 5 A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12" and Sectoin 2 has a…

Q: Two tanks A and B have 80 m difference in water levels, and are connected by a pipe 0.3 m diameter…

A: Friction factor f = 4F = 4×.002 = .008 Total inflow = Total net flow at junction CQ1 = Q2 + Q3Q1 =…

Q: Water with sp.gr 0.97 flows through a pipe of uniform diameter 350mm with a mean velocity of 1.0…

A: SG = 0.97 D = 350 mm or 0.35 m V = 1 m/sP1 or 250,000 Pa

Q: Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section…

A: Given- Head difference between point 1 & 2 = 1.5 m, Discharge Q=0.9 m3/s, Diameter at section 1…

Q: Piezometric tubes are tapped into a pipe section as shown in the figure below. The liquid is…

Q: Problem #1 (Pipes Iterative Analysis): Water at 70°F flows through 100 feet of pipe 10 inches in…

A: Given, T=70°F Length of the pipe L= 100 feet D= 8 inches =0.67 m ε=0.00085 ft Head loss in pipe…

Q: Reservoirs A and B with water levels at 72 m and 57 m respectively above datum are connected to a…

Q: Water flows from reservoir A to B through the three concrete pipes shown below. Assume that concrete…

A: GivenH=20mL1=2500md1=400mm or D1=0.4mL2=1850m, d2=300mm or D2=0.3mL3=800m, d3=200mm or…

Q: A city needs to transport 1,800 m3/day of water at 4 C from a reservoir to a holding tank for a…

A: Given: Discharge, Q=1800 m3/day Length, L=8 km=8000 m Slope=1:500

Q: Q2. Oil with an absolute viscosity of 0.125 N.s/m² and a density of 890 kg/m' is flowing in a 16.5…

A: Given data Dynamic viscosity Density Diameter Discharge. We will first find is it a laminar or…

Q: The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and…

A: g =9.81m/s2 = 32.185 ft/s2 Q1 = 50ft3/s

Q: The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the…

Q: A

Q: Q1: For the figure shown, determine peak flow at manhole M2 at 10 min after rain started. Consider…

Q: A Venturi Meter has water is flowing through the Venturi Meter, the pressure in the pipe and the…

A: Given, D = 0.2 m d = 0.06 m ∆P/γ = 0.15 m

Q: A 11 inches pipe is being tested to evaluate the lost head. When the flow of water is 6.31 cfs, the…

A: Differential gauge: The device used to evaluate the difference between two points having different…

Q: A pipe carries a flow of 5.17 cfs of oil (SG = 0.877). At one diameter is 6 inch, the pressure is…

A: Flow of oil in the pipe, Q = 5.17cfs , Specific Gravity of oil = 0.877 , d1= 6 in , p1= 13.2 psi =…

Q: PROBLEM O3: Given the figure below, (a) determine the flow rate in the siphon shown. Diameter of the…

Q: A wastewater pump is discharging at a rate of 0.5 m3/s. It has a discharge nozzle diameter of 350 mm…

A: According to given data A wastewater pump is discharging at a rate of 0.5 m3/s.It has a discharge…

Q: Water is siphoned from the tank as shown in the figure below. the length of the pipe is 12 m and has…

A: Diameter of Siphon d = 400mm length of siphon = 12m Roughness ratio = 0.001 a) Neglecting all the…

Q: The flow rate in a 300 mm diameter pipe is 0.226 m³/s. The flow is known to be turbulent and the…

Q: For the pipe network shown, the flow of water from A to the first junction is 0.055 cubic meter per…

A: as per the our guidelines we are suppose to solve only 3 subpart prepost question . kindly repost…

Q: The three water-filled tanks shown are connected by pipes as indicated. If minor losses are…

A: Pipe 1: Elevation: Diameter of pipe: Length of pipe: Friction coefficient: Pipe 2: Elevation:…

Q: A pump is installed in the pipeline between reservoirs A and E as shown in the figure below. Water…

A: Given, Hazan Williams coefficient =120 discharge Q=10 ft3/s Elevation A and B is 25ft and 40 ft

Q: A horizontal pipe gradually reduces its diameter from 300 mm at point A to 100 mm at point B. The…

A: dia at A(DA)= 300mm=0.3marea at A(AA)=dia at A(DB)= 100mm=0.1marea at B(AB)=pressure at A(PA)= 100…

Q: Problem 6: EGL and HGL (II) Part A Why is the energy gradient (i.e., the slope of the EGL=EL) larger…

A: This question is related to the Fluid mechanic from Civil Engineering.In this question ask about the…

Q: Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line…

A: The pressure head,

Q: Water resources engineering Please refer to the attached image. The new cat iron pipe carrying a…

A: Given data: Flow in pipe is 0.3 ft3/s. Elevation at reservoir surface is 1300 ft. Elevation at point…

Q: A fluid with unit weight of 6.67 kN/m' flows, from a 0.3 m diameter pipe inside of which the…

A: The given data is: Unit weight of fluid=6.67 kN/m3 inside diameter pressure=300 kPa outside diameter…

Q: Given the set-up shown in the illustration, find the following: a. Equivalent coefficient of…

Q: In the branched pipe system shown, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40…

A: Data given Q = 850 L/min = 0.0141 m3/s Total length of pipe in the lower branch, L2 = 60 m L1 = 30…

Q: Reservoirs A and D are connected by a pipeline system as shown below. The water surface elevations…

A: Given, Surface elevation of reservoir A = 100 ft Surface elevation of reservoir B = 80 ft

Q: You are designing a flocculation basin to handle an average daily flow of 8 MGD with a temperature…

A: Given data Discharge Time Velocity gradient

Q: A steel pipe has an inside diameter of 25mm, is 20 meter long, carries 10degree water at the rate of…

A: what is the static pressure of the water at the outlet,P2=?

Q: Using the Hazen-Williams nomograph determine the following: a. The head loss as 5.6 liters/s of…

Q: 0 ft (assume this is 1000.00 ft). The flowrate in the system from ervoir is 5 cfs. Assume the water…

A: Solution- (a) Hazen williams equation: hf =4.73lQC1.852-1d4.87 here , For first 1000 ft…

Q: 3. Three concrete pipes are connected in series as shown, if the rate of flow in the pipe is 3.53…

Q: For the parallel pipe system shown below, the elevation of point A is 300 feet and a pressure of 30…

A: Pressure at point A =30psi = 4320lb/ft2Elevation of point A =300ftPressure at point B = 27psi =…

Q: Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B…

Q: The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the…

A: Calculation of pipe bend problem

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

A straight pipe has a diameter of 25 mm, a roughness height of 0.1 mm, and is
inclined upward at an angle of 10°. The pipe transports water at 20° C
Part A
If the pressure at a given section of the pipe is to be maintained at 550 kPa,
determine the pressure at a section 100 m downstream for flows of
2 L/min.
Express your answer to three significant figures and include
appropriate units.
μA
?
715
kPa
Submit Previous Answers Request Answer
X Incorrect; Try Again; 4 attempts remaining
7 Part B
If the pressure at a given section of the pipe is to be maintained at 550 kPa,
determine the pressure at a section 100 m downstream for flows of
20 L/min
Express your answer to three significant figures and include
appropriate units.
0
μA
C?
674
kPa
Submit
Previous Answers Request Answer
X Incorrect; Try Again; 5 attempts remaining

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Trending now

This is a popular solution!

Step by step

Solved in 10 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

PROBLEM 2 The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and discharge Q1 = 50 ft/s. Determine the following: (a) head loss (ft) in pipe 1, hu, (b) the elevation (el D') of the imaginary water surface at the junction, (c) the head loss (ft) in pipe 2, hua, (d) the flow rate (ft/s) in pipe 2, Q2. (e) the flow rate (ft/s) in pipe 3, Qa. (f) the head loss (ft) in pipe 3, ha, (g) the elevation of the surface of reservoir C, EI C. pipe L (ft) | d (in) 1 5000 36 0.0157 1500 24 0.0162 3 4000 18 0.0177 D
PROBLEM 2 The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and discharge Q1 = 50 ft/s. Determine the following: (a) head loss (ft) in pipe 1, hu, (b) the elevation (el D') of the imaginary water surface at the junction, (c) the head loss (ft) in pipe 2, h2, (d) the flow rate (ft/s) in pipe 2, Q2. (e) the flow rate (ft/s) in pipe 3, Q3. (f) the head loss (ft) in pipe 3, h3, (g) the elevation of the surface of reservoir C, El C. pipe L (ft) d (in) 5000 f 1 36 0.0157 2 1500 24 0.0162 3 4000 18 0.0177 A B
Water at 20°C is pumped at a rate of 15 L/s into a reservoir as shown in the Figure below. Between the pump and the reservoir is 150 m of 100 mm diameter PVC pipe, and the water surface elevation in the reservoir is 8 m above the centerline of the inflow pipe. The roughness height of the PVC pipe can be assumed to be negligibly small. Estimate the gauge pressure (kPa) on the downstream side of the pump. 15 L/s 133 120 111.7 131.5 Pump P - 150 m. 100 mm Reservoir 8m
Figure Q1 shows an internal piping system of a building. The pipe is uPVC of total length 35 m. The minor loss coefficients are as shown in the figure. The flow velocity in the pipe is designed to be 1.0 m/s and the residual pressure head at appliance X must be at least 0.8m. Determine the required pipe diameter using Darcy Weisbach formula. Level 8.5 m k = 0.8 Water tank IT Roof beam Minor loss coefficients: E Stop valve, k = 10 O 90°elbow, k = 1 Level 4 m Figure Q1
Need a complete answer with illustration Two pipes with C1 = 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft. If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.
8. Water is flowing in a 100 mm diameter Mild Steel (MS) pipe of length 180 m as shown in the figure. The reservoir water level remains constant. Determine the flow rate. Use the following methods: (a) Darcy Weisbach formula with loss coefficient method, (b) Darcy Weisbach formula with effective pipe length method, (c) Hazen William's formula with loss coefficient method, and (d) Hazen William's formula with effective pipe length method. (Ans.: 28.27 liter/s, 28.33 liter/s, 32.04 liter/s, 32.67 liter/s) EL85 m EL = Elevation Gaie valve Butterfly valvé opened EL50 m
Oil flows at 62 L/s in a pipe of 175mm diameter and 50m length. SG of oil is 0.9 and viscosity is 0.04 Pa-sec. If head loss is 5.22m, determine: a) Mean velocity of flow = [ Select ] m/s b) Type of flow = [ Select ] %3D c) Friction factor = [ Select ] d) Velocity at the centerline of pipe = [ Select ] v m/s e) The shear stress at the wall of the pipe [ Select ] Ра %3D
2.10. Water leaves a treatment plant in a 500-mm diameter ductile-iron pipeline at a pressure of 600 kPa and at a flow rate of 0.50 m³/s. If the elevation of the pipeline at the treatment plant is 120 m, estimate the pressure in the pipeline 1 km downstream where the elevation is 100 m. Assess whether the pressure in the pipeline would be sufficient to serve the top floor of a 10-story building (approximately 30 m high).
A PIPELINE WITH A PUMP LEADS TO A NOZZLE AS SHOWN. FIND THE FLON RATE WHEN PUMP DEVELOPS AN 80FEET HEAD. ASSUME HEAD LOST IN THE 8-INCH PIPE TO BE THERE TIMES ITS VELOCITY HEAD WHILE THE HEAD LOST IN THE 4-INCH PIPE TO BE TEN TIMES VELOCITY HEAD. FIND: a)COMPUTE THE FLOW RATE b) FIND THE PRESSURE HEAD AT THE SUCTION SIDE. PLEASE ANSWER IMMEDIATELY WITH COMPLETE SOLUTION THANK YOU!
Q3. SAE 30 oil (Sp. Gr. =0.833) with a dynamic viscosity 0.28 N.S/m? flows in a 4-cm-diameter pipe which is inclined with an angle 37°. For the pressure measurement shown, determine A. Whether the flow is up or down The flow rate in m'/h C. The shear stress and velocity 1 cm from the boundary Draw the shear stress and velocity profile with the section of the pipe. В. D. P-180 kPa P- sOokPa 15m 20m
A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az
Water flows through a concrete pipe 3 ft in diameter between reservoir A and reservoir B. The surface of reservoir A is at 800 ft while the surface of reservoir B is at 300 ft elevation. The length of the pipe is 1000 ft. Calculate: a. the head loss through the pipe b. the flow rate in the pipe