A steel tube, with a thermal conductivity of 50 W /m K, has an inner diameter of 20-mm and outer diameter of 26-mm. Hot gases flow over the tube with a convection heat transfer coefficient of 200 W/m2 K; while, cold water flows through the tube with a convection heat transfer coefficient of 8000 W/m2 K. What is the cold-side overall heat transfer coefficient in W/m2 K?

A steel tube, with a thermal conductivity of 50 W /m K, has an inner diameter of 20-mm and outer diameter of 26-mm. Hot gases flow over the tube with a convection heat transfer coefficient of 200 W/m2 K; while, cold water flows through the tube with a convection heat transfer coefficient of 8000 W/m2 K. What is the cold-side overall heat transfer coefficient in W/m2 K?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel tube, with a thermal conductivity of 50 W /m K, has an inner diameter of 20-mm and outer diameter of 26-mm. Hot gases flow over the tube with a convection heat transfer coefficient of 200 W/m2 K; while, cold water flows through the tube with a convection heat transfer coefficient of 8000 W/m2 K. What is the hot-side overall heat transfer coefficient in W/m2 K?
can you please please do this one and please show all the work please step by step
2- The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick. There are to be 100 fins per meter. The convective heat transfer coefficient, both for the wall and the fins, is estimated at 35 W/(m2 K). With this information, determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall. (take the case where the tip is exposed to convection) Ans(48 t= 2.5 mm 2.5 cm
The flow of water entering a pipe is 0.25 kg / s and its temperature is 20 ° C. The diameter of the pipe is 20 mm and the wall temperature of the pipe is 100 ° C. If the average value of the heat transfer coefficient is 700 W / m C, what is the length of the pipe required to raise the water temperature to 80 ° C?
. Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k = 2.3 W/m °C, and surface area A = 20 m². The left side of the wall is maintained at a constant tem- perature of T₁ = 80°C while the right side loses heat by con- vection to the surrounding air at T = 15°C with a heat transfer coefficient of h = 24 W/m². °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat trans- fer through the wall. Answer: (c) 6030 W
Water flows through a cast steel pipe with k = 53 W/m-K with an outer diameter of 110 mm and 3.5 mm wall thickness. Calculate the thickness of insulation to be lagged on the pipe if the heat transfer per unit length is 6.5 W/m. The thermal conductivity of the insulation is 0.045 W/m-K. The water temperature is 15°C with convective heat transfer coefficient of 30 W/m2 -K while the outside air is -8°C and 18 W/m2 -K.
A pipe carrying hot gasses is insulated with a material having a thermal conductivity of 0.15 W/mK. The average local heat transfer coefficient by convection to the ambient air is 3 W/m K. The critical diameter of the pipe under 35. these conditions is (a) 100 mm (c) 160 mm (b) 130 mm (d) 200 mm
2. A copper tube with 8 cm outer diameter, 6 cm inner diameter and k = 15 W/m-K is covered with an insulation covering of thickness 3 cm and k = 0.2 W/m-K. A hot gas at 300°C with hi= 400 W/m²-K flow inside the tube. The outer surface of insulation is exposed to cool air at 30°C with ho = 50 W/m²-K. Find the overall heat transfer coefficient.
A 0.5-ampere current is flowing through a long electrically conducting cylindrical rod. The diameter of the rod is 6 mm, the electrical resistance of the rod is R = 2000 /m, and k =0.9 W/m K for the rod. The rod is encased in a 2-mm thick Pyrex tube and a 20°C liquid is flowing over the outer surface of the Pyrex tube. The convection heat transfer coefficient for the liquid h= 800 W/m2 . K. The interfacial conductance (contact resistance) at the interface between the rod and the Pyrex tube is h = 1200 W/m² - K. a) Compute the rate of heat generation in the rod and use it compute the volumetric rate of heat generation. b) Find the temperature drop across the interface between the outer surface of the rod and the inner surface of the Pyrex tube. c) Find the temperature at the center of the rod.
The temperature of a gas stream is measured by a thermocouple whose junction can be approximated as a 1-mm-diameter sphere. Take the junction’s properties as: k of 32 W/m K, density of 8.2 kg/m^3, c of 300 J/Kg K. On its surface, the overall heat transfer coefficient is 200 W/m^2 K. Neglect any conduction loss from the sphere to other parts of the thermocouple. Create a plot of measurement error as a function of time for the thermocouple, expressed as a fraction of the initial temperature difference.