WhatsApp .ll 3G9:44 AM81%Assignm.AssignmentA steel tape of nominal length 30m was used to measure a line AB by suspending it betweensupports. The following measurements were recordedtension appliedLine Length measured slope angle mean temperature3°40AB29.872120NThe standardized length of the tape against a reference tape was known to be 30.14m at 20°and 50N. If the tape weighs and has a cross sectional area of 2mm?, calculate the horizontallength of AB. Young's modulus (E) for the tape is 200 and the coefficient of thermal expansion(a) is 0.0000112 per °C

Answered: Image /qna-images/answer/5bd73f2a-b7a2-437f-9b6a-72cbe08031ee.jpg

A steel tape of nominal length 30m was used to measure a line AB by suspending it between supports. The following measurements were recorded Line Length measured slope angle mean temperature tension applied AB 3°40 29.872 5° 120N The standardized length of the tape against a reference tape was known to be 30.14m at 20 and 50N. If the tape weighs and has a cross sectional area of 2mm, calculate the horizontal length of AB. Young's modulus (E) for the tape is 200 and the coefficient of thermal expansion (a) is 0.0000112 per °C

A steel tape of nominal length 30m was used to measure a line AB by suspending it between supports. The following measurements were recorded Line Length measured slope angle mean temperature tension applied AB 3°40 29.872 5° 120N The standardized length of the tape against a reference tape was known to be 30.14m at 20 and 50N. If the tape weighs and has a cross sectional area of 2mm, calculate the horizontal length of AB. Young's modulus (E) for the tape is 200 and the coefficient of thermal expansion (a) is 0.0000112 per °C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation #1: Find the value of the diameter at point B. d, = 150 mm V = 1.5 m/s A B d, = ? V, = 2.5 m/s
If the section shown in the figure turns from fully-elastic to fully-plastic, the depth of neutral axis (N.A), y, decreases by 60 y I 5 4 N.A. *20* ]] 60
Problem 2 For the simply supported beam shown below, determine whether the beam is cracked or un-cracked under the applied loads, use f'e = 25 MPa, if the beam is cracked calculate the bending stresses in the beam using the transformed area method. 20 KN 300 mm 4 kN/m A↓ D 3025 k 3 m 3 m 500 mm - աա St
Show full solutions.
can u help Write a brief conclusion on the answer that you obtain from the above question. Is it liable and okay to obtain this amount of error? Explain your point of view.
A steel tape standardized at 20degree celcius and supported through out under tension of 90N Was found to be 30.377m long. The tape had a cross sectional area of 55mm^2 and a weight of 73g/m. This tape was used supported at the ends only with a constant tension of 78N to measure a line from A to B in nine segments. The data given in the following table were recorded. Apply correction for tape, length,temperature,pull,sag and tape not horizontal to determine the correct length of the line Difference in Elevation Cm) 0-392 Section Meacured Recarded Distance) Tempergrare A-1 15 1- 2 30 15 0.301 2-3 30 16 O.191 3-4 16 0-255 4-5 30 16 0-38 5-6 30 8.636 6-7 0.782 7-6 30 0-825 8-8 25.348 18 0.578 Sum = 265-348 m
*PLEASE WRITE THE SOLUTION *THE ANSWERS MUST BE IN 4TH DECIMAL PLACE Need in 30mins at most 1hr...
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
-Problem XYZ. A steel tape is 100 m long at a standard pull of 65 N. Compute the pull correction in mm if during measurement the applied pull is 40N. The tape has a cross sectional of 3.18 mm^2 and E=200GPa. If the measured length of the line is 865.30, what is the corrected distance? CHOICES: A. 3.93MM, B. 3.94MM, C. 3.95MM, D. NONE OF THE ABOVE -On Problem XYZ. If the measured length of the line is 865.30, what is the corrected distance? CHOICES: A. 865.266, B. 865.301, C. 865.27, D. NONE OF THE ABOVE
Question 9... use three decimal places
what will be the equivalent value of P that can be applied if the maximum vertical displacement allowed is 5mm??
Find ?? (epsilon x), ?? (epsilon y) and ? (gamma) . NOTE: ?? (epsilon x) ??? ?? (epsilon y) in mm/mm and ? (gamma) in radians. Indicate elongation or contraction for the normal strains. Use 3 decimal places. Use 2 decimal places in every solved value.