A Steel shaft is subjected to an end thrust producing a stress of 90 MPa and the minimum shearing stress on the surface arising from torsion is 60 MPa .The yield point stress of the material in simple tension was found to be 300 MPa. calculate the factor of safety of the shaft according to the following theory 1)maximum shear stress theory

Q: The ultimate stress for the hitch ball is 60,000 ksi. (Capacity) The advertisement information is…

A:

Q: 100 kip 10 kip-ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of…

A: solution Given d=4 in

Q: A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside…

A: A) Angle of twist for the given max shear stress in a hollow shaft: The angle of twist of a hollow…

Q: The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when…

A:

Q: Let's consider a solid circular shaft subjected to the torque loads as shown. Determine the minimum…

A:

Q: 4. As shown below, the prosthesis is made of two parts a core (G=150 ksi) and a tube (G=85 ksi). The…

A: Write the torsion equation. Here, T represents the torsional torque, J represents the polar moment…

Q: A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength…

A: E=205 GPaσy=250 MPad0=45 mmt=3 mmdi=45-2×3di=39 mmL= 4 ma if torque T=580 Nm then shear stress…

Q: The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid…

A: The power supplies by motor is The speed of motor is The diameter of shaft 1 and 2 is The modulus of…

Q: A bar of steel has the minimum properties Se= 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is…

A: Given:The endurance stress is The yield stress is The ultimate stress is The steady torsion stress…

Q: A shaft consisting of an aluminum segment and a steel segment is acted upon by two torques. The…

A: The diameter of the aluminum section is The diameter of steel section is  The shear modulus of…

Q: Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A:

Q: Figure 2 shows a solid shaft consisting of two prismatic circular parts in equilibrium under the…

A:

Q: 2. A element was made of a material with the material parameters of a b MPa, os 600MPa, o-1-360MPa,…

A: Given:To find:

Q: The copper pipe (G= 50 GPa) is tightly secured to the wall at A, has an outer diameter of 40 mm and…

A: The objective of the question is to determine the maximum shear stress developed in the copper pipe…

Q: 1- A cylindrical rod with a diameter of 20 mm and length of 100 mm is simultaneously subjected to a…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.