A steel plate subjected to a force of 5 kN and fixed to a channel by means of three identical bolts is shown below. The bolts are made of plain carbon steel 30C8 with yield strength of 400 MPa and the factor of safety is 3. Determine the diameter of the shank. 5 kN 75 75 3- 250-

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: What is Line B?

A: Solution:

Q: F= 200 N %3D 30° 13 12 F2 = 260 N

A:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: For the objects shown in isometric views in the space provided. Make below, sketch the t sure that…

A: According to the details provided in the question we need to find three projection view as below.

Q: n the figure, front (1st picture) and left (2nd picture) views of a machine part are given. Based on…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Given the multiview projection of the solid, draw the isometric view. HRP FRP F DA FRP PRP

A: Given the multiview projection of the solid, draw the isometric view.

Q: Draw the plan, Front view and the Side view of the following figure and do the dimensioning.

A: Please refer the following orthographic views of the given object.

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: 0.50 1.25 3.00 1.00- 2.00 1.00

A: Given,

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Find area of the shaded part using inventor

A: Find Find the area of the shaded part.

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: On the first picture, you have the length of the triangle as 300. If the total length of the door is…

A: Here you are asking why the length of the triangle is 300 and not 440.

Q: Given the top and front views, sketch the right face.

A: According to the details provided in the question. Top view and front view is given we need to draw…

Q: Many aspects of a gymnast's motion can be modeled by representing the gymnast by four segments…

A: Draw the given table.

Q: Rotate the objects shown below by the indicated amount and sketch the result in the space provided.…

A:

Q: The vertical distance above a reference datum to a point is called the point’s

A: ▪︎We have to specify the term related to the vertical distance above the reference datum to a point.…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Partition the given figure and find the x and y coordinates.

A: Task at hand is to find the centroid of the shape in the figure

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.