A steel plate has dimensions of 3 m by 1 m and is initially kept at a temperature of 30 degree Celsius. It is cooled by blowing air parallel to the 1 m edge at 9 km/hr. The temperature of the flowing air is maintained at 10 degree Celsius. Estimate the convection heat transfer rate from both sides of the plate.

A steel plate has dimensions of 3 m by 1 m and is initially kept at a temperature of 30 degree Celsius. It is cooled by blowing air parallel to the 1 m edge at 9 km/hr. The temperature of the flowing air is maintained at 10 degree Celsius. Estimate the convection heat transfer rate from both sides of the plate.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
Calculate the convective heat transfer rate via the top and the two side walls of a refrigerated box trailer as shown in the figure. The trailer is cruising at a rate of 70 mph (31.3 m/s). The box trailer dimensions are 16 m long, 4.1 m high, and 2.6 m wide. Assume that the surface of the trailer is at uniform temperature of 10°C. The air temperature is 30°C. Because of the presence of the prime-mover in the front, the air flow can be assumed to be turbulent when it encounters the trailer. 187.4 kW Walls. Prime-mover 16 m 2.6 m
The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and 20°C flows with a velocity of 8 m/s over a 1.5 m * 6 m flat plate whose temperature is 140°C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side and (b) the 1.5 m side.
Water at 43.3°C flows over a large square plate at a velocity of 28 cm/s. The plate is 1.2 m long (in the flow direction) and its surface is maintained at a uniform temperature of 10.0°C. The width of the plate is 1.2 m. Calculate the steady rate of heat transfer for the entire width of the plate in watts (W). The properties of water at the film temperature of (Ts + T∞)/2 = (10 + 43.3)/2 = 27°C are ρ = 996.6 kg/m3, k = 0.610 W/m·°C, μ = 0.854 × 10–3 kg/m·s, and Pr = 5.85. The steady rate of heat transfer per unit width of the plate is ___ W.
Q9) Consider a 50 cm diameter and 95 cm long hot water tank. The tank is placed on the roof of a house. The water inside the tank is heated to 80°C by a flat-plate solar collector during the day. The tank is then exposed to windy air at 18°C with an average velocity of 40 km/h during the night. Estimate the temperature of the tank after a 45 mm period. Assume the tank surface to be at the same temperature as the water inside, and the heat transfer coefficient on the top and bottom surfaces to be the same as that on the side surface.
The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and at 30°C flows with a velocity of 4.8 m/s over a 2.3-m × 8-m flat plate whose temperature is 120°C. Determine the rate of heat transfer from the plate if the air flows parallel to the 2.3-m-side. The properties of air at 0.823 atm and at the film temperature of (120 + 30)/2 = 75°C are k = 0.02971 W/m·°C, ν = 2.486 × 10-5 m2/s, and Pr = 0.7166.
Principles of Convection Heat Transfer EXAMPLE 7: Air at 5°C and 70 kPa flows over a flat plate at 6 m/s. A heater strip 2.5 cm long is placed on the plate at a distance of 15 cm from the leading edge. Calculate the heat lost from the strip per unit depth of plate for a heater surface temperature of 65°C.
Q : Engine oil at 80°C flows over a 10-m-long flat plate whose temperature is 30°C with a velocity of 2.5 m's. Determine the rate of heat transfer over the entire plate per unit width. Take the properties of the oil at film temperature
A 15 cm x 15 cm circuit board dissipating 15 W of power uniformly is cooled by air, which approaches the circuit board at 20°C with a velocity of 5 m/s. Disregard any heat transfer from the back surface of the board and evaluate properties of air at 300 K. Assume the flow to be turbulent across the entire length of the board since the electric components will have tripped the boundary layer. (a) Determine the surface temperature of the electronic components at the leading edge of the board, and (b) at the end of the board. (c) Ideally, at what temperature would the properties of air be evaluated at?
Oil flow in journal bearing can be approximated as parallel flow between two large plates with one plate moving and the other stationary. Determine the velocity, temperature distributions, the maximum temperature, the rate of heat transfer and the mechanical power wasted in oil. Take properties of oil at 50°C are given to be, k=0.17W/m. K, and u=0.05N.s/m2.
Water at 43.3°C flows over a large square plate at a velocity of 20 cm/s. The plate is 2 m long (in the flow direction) and its surface is maintained at a uniform temperature of 10.0°C. The width of the plate is 2 m. Calculate the steady rate of heat transfer for the entire width of the plate in watts (W). The properties of water at the film temperature of (Ts + T∞)/2 = (10 + 43.3)/2 = 27°C are p = 996.6 kg/m³, k= 0.610 W/m-°C, μ = 0.854 x 10-3 kg/m-s, and Pr = 5.85. The steady rate of heat transfer per unit width of the plate is W.