A steel ball is resting in a trough as shown in the figure. The weight of the ball is 1000 N. Determine the reactions developed at the contact surfaces. The inclination of the surface with the horizontal is e, = 30°. Assume all contact surfaces are smooth. e1 enwers in the enarate submission link

A steel ball is resting in a trough as shown in the figure. The weight of the ball is 1000 N. Determine the reactions developed at the contact surfaces. The inclination of the surface with the horizontal is e, = 30°. Assume all contact surfaces are smooth. e1 enwers in the enarate submission link

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The mass center G of the 1405-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. 1382 mm-859 mm Answers: Normal force under each of the front tires: N- N Normal force under each of the rear tires: N, - N i i
The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.
Two farmers are pushing on a gate with forces Fa and FB, applied at locations A and B respectively. The gate has a hinge at Cand you may neglect the thickness of the gate. Assume that the gate is in static equilibrium. The force FA is applied at an angle of a = 35° and the force Fg is applied at an angle of 3 = 70°. The distance between Band the hinge at Cis DBC = 1.5 m, and the distance between A and the hinge at Cis DAC = 2 m. Suppose that |FA| = 100 N. Aa Dac a) Draw a Free Body Diagram to represent this set-up. b) Write down the equations for static equilibrium. c) Calculate the moment about C, leaving your answer in terms of the unknown force magnitude | Fg|- d) Calculate Fa|-
Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square hole in the collar fixed to the member as shown in the figure. Suppose that F1 = 190 N, F2 = 390 N and the rod holds in equilibrium. Determine the components of reaction force at A using scalar notation and tension in the cable. Determine the components of the moment of reaction at A using scalar notation.
The lid shown has a mass, m = 60 kg, and is held in position by rod AB. The rod is held in place by rounded surfaces at A and B, where B is right at the edge of the lid. The hinges at C and D rotate smoothly and only the hinge at C provides a reaction force along its axis (the x-direction). a = 950 mm, b = 300 mm, c = 55 degrees Determine A) Reactions at hinge C and D B) Reaction force in rod AB C) The minimum coefficient of friction that is needed between the rod and the lid to maintain this position
answer is B=14.528lb D= 14.58lb F= 3lb, but I need help to get to them 1. For the frame below a. Use a free body of the full structure to find the reactions at Pin A and Roller B. b. Determine the magnitude of the forces on pins B, D, and F. Show your ree oeY diagrams. 30 in-lb 10 lb 6" 7" 4" 3" 4" 3" 1. 1.25"
Problem: The elements of a wall-mounted swing-away stool are shown in the figure. The hinge-pin P fits loosely through the frame tube, and the frame tube has a slight clearance between the supports A and B. Determine the reactions on the frame tube at A and B associated with the weight L of an 80 kg person. Also, calculate the changes in the horizontal reactions at C and D due to the same load L. State any assumptions. 65 mm Al 175 mm B 65 mm D 350 mm 85 mm
The L bar is supported by a universal gasket at O and by the two wires as shown. The universal joint can withstand, in addition to the three reaction forces, a moment on the y axis but not on the x and z axis, find the reactions for when the load is in x = 1 m. (b) 1.2 m 1.8 m 0.3 m. 0.6 m E B 2.1 m -1.5 m 50 kg
The frame shown is supported by a hinge (pin) at A and a roller at E. the frame is subject to three forces F1 = 410 N, F2 = 190 N and F3 = 250 N as shown in the figure below. If the frame is in equilibrium, Determine 1.25 m F2 3 m 2 m 2 m F3 A. Reactions at A Ax = Ay = B. Reactions at E Ex = Ey =