ring 2020-2021.paf *5-88. Determine the horizontal and vertical components of reaction at the pin A and the force in the cable BC. Neglect the thickness of the members. 30 200 N/m 45m

Q: O and EFy 0. Do not solve. %3D P1-3. Write the two equations of equilibrium, EFx =

A:

Q: Determine the horizontal component of reaction at the pin A to support the steel frame if force F =…

A:

Q: he forklift supports the engine. Determine the force that generates this load on element DB. Write…

A: Given data as per question Engine mass = 114 kg =1118.34 N a = 1.47 m b = 1.81 m Considering FBD of…

Q: a block is held in equilibrium by the system of springs. Draw a free-body diagram for the ring at A.…

A:

Q: 1. The overhanging beam is supported by a pin at A and the two-force strut BC. Determine the…

A: FBD                     θ = tan-11.52θ = 36.89°

Q: If a force of P=25N is applied to the handle of the mechanism, determine the  force the screw exerts…

A:

Q: Determine the reaction at support B using Force method analysis. Assume support A is fixed and…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 580 lb, a = 2.9 ft, b = 2.4 ft, r = 8 in.…

A:

Q: The 540-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A: Given Data

Q: 2 kN/m 2 m 10 kN 4 m 2 m 5m

A: Determine the point load corresponding to the point load. W=2 kN/m·5 m=10 kN So a point load of 10…

Q: *R5-8. Determine the resultant forces at pins B and C on member ABC of the four-member frame. -1.25…

A: The free-body diagram of the frame showing the reactions at joints can be sketched as follows,

Q: 20 N/m KAC www !3! 3 m

A: given:

Q: Determine the magnitude of the pin force at A.

A:

Q: Determine the magnitude of the pin force at A. Assume W = 510 lb, a = 3.0 ft, b = 2.0 ft, r = 6 in.…

A:

Q: The steel plate is 0.4m thick and has a density of 7050 kg/m3. Determine the location of its center…

A:

Q: A 300kg counterweight with center of mass at G is mounted on the AB crank rod of the oil pump unit.…

A: Given Data Torque supplied by motor is : M=250 Nm  Mass of the counter weight mounted on crank AB…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: We have loaded truss members . To find the force acting in different members, we will 1st draw FBD…

Q: 6-70 Determine the horizontal and vertical components of force at pins B and C. The suspended…

A:

Q: The three A-36 steel wires each have a diameter of 2 mm and unloaded lengths of LAC = 1.60 m and LAB…

A: This type of problem is called statically indeterminate , since the equilibrium equation(s) are not…

Q: 1. the cable is wrapped around the pulley and attached vertically at A. The bearing B only allows…

A: According to the question F=10i-30j-10k N We need to find The tension in the rope

Q: The pole is subjected to the two forces shown. Determine the components of reaction of A assuming…

A:

Q: Determine the magnitude of the horizontal force F and the support reactions at . If the cord CB ean…

A: Given: To determine: Reaction force at pin A

Q: -127. Determine the clamping force exerted on the mooth pipe at B if a force of 20 lb is applied to…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 790 lb, a = 4.1 ft, b = 3.0 ft, r = 8 in.…

A:

Q: P5-3. then draw the free-body diagrams of each member of the identify any two-force members, and…

A: If in an element no load or force is acting between the pins or hinge supports at both ends then…

Q: Draw the free-body diagram of each object and determine the components of the support reaction

A: According to the given data We need to find the reactions at point-A and B

Q: Draw the free-body diagram The plate is made of steel which has a density of 7850 kg If the…

A: Given Data Density of steel plate is : ρ=7850 kg/m3 Thickness of the plate is :t=1 cm=0.01 m Now a…

Q: 6-58. The space truss is used to support the forces at joints B and D. Determine the force in each…

A: Using method of joints:Joint D:Joint C:Joint B:

Q: 2. The wall crane supports a horizontal and vertical compo D. Also, what is the force in ABC has a…

A: The force equilibrium at point E is-

Q: W=25N, h=60mm. Find the spring force acting on the member DE and the reactions of the support at F.

A: Given data: The value of weight is, W=25 N. The value of height is, h=60 mm For member AB,

Q: 3–18. If the spring DB has an unstretched length of 2 m, determine the stiffness of the spring to…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: For the curved beam, determine the horizontal and vertical components of force at pin A and vertical…

A:

Q: The ramp of a ship has a weight of 250 lb and a center of gravity at G. Determine the cable force in…

A: Given: W = 250 lb

Q: P5-3. then draw the free-body diagrams of each member of the identify any two-force members, and…

A: Break the given frame into two parts AB and BC. Understand that the Uniformly varying load can be…

Q: Determine the internal normal force at point F in the frame. The crate weighs 151 lb.

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.