A steel alloy bar 100 mm long with a rectangular cross section of 10 mm * 40 mm is subjected to tension with a load of 80 kN and experiences an increase in length of 0.1 mm. If the increase in length is entirely elastic, calculate the modulus of elasticity of the steel alloy.

Q: In the figure below, a stainless steel wire is supporting a weight, W. The Yield Strength and…

A:

Q: Which of the following is the best representation of the samples' (A and B) axial strains when…

A:

Q: A steel alloy bar 100 mm long with a rectangular cross section of 10 mm X 40 mm is subjected to…

A: Concept: Since it has been given that the material is linearly elastic within applied load, the…

Q: A steel of cross-section area 100 mm² and 1 m long is subjected to a tensile force of 40 kN. What is…

A:

Q: A steel bar 4 inches long and having a square cross section 0.8 inches on an edge is pulled in…

A:

Q: The graphs in figure 5 show how tensile stress varies with tensile strain for two metallic wires…

A: Breaking stress :  It is the maximum stress at which a material can take before it fails. For copper…

Q: An aluminum specimen originally 300 mm long is pulled in tension with a stress of 275 MPa. If the…

A: Hooke's law: With in the elastic limit , Stress is always directly proportional to strain. when we…

Q: An aluminum tensile test specimen has a diameter, do = 25 mm and a gauge length of Lo = 250 mm. If a…

A: Given : do = 25 mm Lo = 250 mm  Force = 175 kN  Elongation of Gauge length = 1.25 mm  This is a…

Q: A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial…

A: given-10.0 mm diameter 1500 N force∆d=0.67 mmn=0.35

Q: The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length…

A:

Q: A cylindrical steel has a length of 3.0m. It weighs 1,000 N and has specific gravity of 7.5.…

A: Please refer the attached image for complete solution. THANK YOU!

Q: A mild steel specimen originally 300 mm long is pulled in tension with astress of 500 MPa. If the…

A: Given: The length of the specimen is 300 mm. The stress is 500 MPa. The modulus of elasticity is 200…

Q: 29. During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of…

A: Given:- The length of the aluminum-alloy rod during testing = 8 inch  The cross-sectional area of…

Q: A mild steel specimen originally 300 mm long is pulled in tension with a stress of 500 MPa. If the…

A:

Q: (a) Tensile stress, (b) the axial linear strain,

A: Given  the length of the steel bar L = 24 in  diameter if the steel bar d = 0.625 in  there fore…

Q: A piece of steel is said to have Young’s modulus of 29 × 106 psi. Based upon a yield strength of…

A: I

Q: A steel bar 106mm long and having a square cross section 20 mm (0.8 in.) on an edge is pulled in…

A: Calculate- elastic modulus of the steel Given- length = 106 mm     -cross section= 20*20 mm² -load =…

Q: A steel bar of 500 mm length is under tensile stress of 100 N/mm?. If the modulus of elasticity is 2…

A: Given data : Length (L)=500 mmTensile stress (σ)=100 N/mm2Modulus of elasticity (E)=2×1011  N/mm2

Q: A tensile load of 150kN is applied to a round metal bar with a diameter of 16mm and a gage length of…

A: Find a.) Modulus of elasticity (MPa)b.) Poisson's ratio for this metal

Q: 9 A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic…

A:

Q: For a material with poisons ratio 0.25, the ratio of modulus of rigidity to modulus of elasticity…

A: Given, Poisson's ratio, v = 0.25 Find, The ratio of modulus of rigidity to the modulus of elasticity…

Q: A tensile test was done on a steel specimen with the gauge length of 525 and a stress of 175 MPa. If…

A:

Q: Question No.2 Figure P1.16 shows the stress-strain relations of metals A and B during ten- sion…

A: It is that point on stress-strain curve, till which stress is linearly varying with strain. As per…

Q: The assembly shown is composed of a steel shell and an aluminum core that has been welded to a rigid…

A:

Q: The following idealized data was obtained from tensile testing of steel. It is required to determine…

A: The stress- stress curve for the given values of stress and strain is as under:-

Q: Problem 3: Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

A:

Q: 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. Stress, psi

A: To calculate maximum working stress, we will have to calculate yield stress. The maximum yield…

Q: Please solve the following problem step by step so I can understand.

A: Solution:

Q: Which is not an elastic constant? O Bulk modulus O Shear Modulus O none of the choices O Modulus of…

A: elastic constants

Q: Consider a square aluminum element of 3in. Dimensions as shown in figure below. If a force is…

A: Poisson's ratio (μ) = 0.33  Deformation along y-axis (δLy) = 0.02 in.  Determine the strain in the X…

Q: Problem 3: Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

A:

Q: (b) (i) A tensile test specimen made from 0.4% C steel has a circular cross section of diameter d mm…

A: Shape of the specimen used is circle of diameter, dGauge length of the specimen = 25 mmLoad applied…

Q: If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and…

A: