A steam pipe line of 150/160 mm in diameter is covered with layer of heat insulating material of thickness 100 mm. Thermal conductivity of tube is 50 W/m deg C or kcal/m-hr-deg C and Ains,mat = 0.09 kcal/m- hr-deg C. Temperature of pipeline inside surface is 400 deg C and temperature of the outside surface of insulating surface is 50deg C. Find loss of heat from length of 1m of pipeline and temperature at interface of insulation.

A steam pipe line of 150/160 mm in diameter is covered with layer of heat insulating material of thickness 100 mm. Thermal conductivity of tube is 50 W/m deg C or kcal/m-hr-deg C and Ains,mat = 0.09 kcal/m- hr-deg C. Temperature of pipeline inside surface is 400 deg C and temperature of the outside surface of insulating surface is 50deg C. Find loss of heat from length of 1m of pipeline and temperature at interface of insulation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are designing a 3m x 3m floor with radiant heating. The floor has 12 parallel pex pipes (k = 40 W/mK) of L = 3m, OD = 25mm and ID = 20mm. Hot water (TInfintiy 1 = 90oC, h = 200 W/m2K) runs through the pipes continuously. The surface below the pipes is perfectly insulated. Above the pipes, there is a 3mm layer of bonding material (? = 12 W/mK) and a 9mm layer of tile (k = 2 W/mK). Above the tile, there is air (TInfinity 2 = 25oC, h = 20 W/m2K). Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), Hint: Assume that the “layer” of pipe starts at the center point (e.g. for conduction purposes, the pipe is OD divided by 2 thick). For convection, consider the entire pipe surface. a) What is the total heat rate entering the room above the floor? b) What is the temperature of the top of the tile?
Steaks (2 cm thick, k = 0.45 W/m - °C, « = 0.91 x 107 m2/s) usually have an original temperature of 25 °C. They will be cooled in a refrigeration room. The said room has a temperature of -11 °C. The heat transfer coefficient on both sides of the steak is 9 W/m2 - °C. How long will it take for both surfaces of the meat to be cooled to 2 °C? Assume the geometry of steaks to be a flat slab.
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTU
A steel bar 7 cm long is welded end to end to a copper bar 3 cm long. Each bar has a square cross section 2.00 cm on a side. The free end of the steel with a temprature at 84 °C, and the free end of the cooper bar is at 12 °C. Find the total rate of heat flow in (W)? (ksteel =50.2 W/K.m and kcopper =385 W/K.m ) (Answer in one decimal places) Material having thermal conductivity k Area A T Steel Соpper T,> T,
Q₁: Find the heat transfer rate by adding straight fins of rectangular cross section of length 50 mm and thickness of 0.5 mm when the heat transfer coefficient from the surface is 40 W/m K and for the fins is 30 W/m°K and k=900 W/m K, surface area (1x1) and distance fins 4 mm. Ans 51526.25
a. The wall of a building has a surface area of 50 m2. The outside layer of the wall is 20 cm thick concrete with thermal conductivity kcon = .8 W/m-K. The inner layer is 10 cm thick balsa wood (kbalsa = .048 W/m-K) as an insulator. Outside temperatures of 47o C are expected, while an inside temperature of 21o C is maintained by the cooling system. Find the rate of heat transfer through the wall.
A pipe carries hot molten lead from one part of a factory floor to another. The mass flow rate of lead is 0.05 kg/s. While trying to figure out the heat loss from the pipe, you found that over a 2-m length of he pipe the lead temperature drops from 580 C to 557.C. What is the rate at which thermal energy is being lost from the lead carrying pipe in this 2-m section? Use the property table to find out properties of lead as needed.
A steel bar 4 cm long is welded end to end to a copper bar 3 cm long. Each bar has a square cross section 2.00 cm on a side. The free end of the steel with a temprature at 63 °C, and the free end of the cooper bar is at 18 °C. Find the total rate of heat flow in (W)? (ksteel =50.2 W/K.m and kcopper =385 W/K.m ) (Answer in one decimal places) Material having thermal conductivity k Area A T2 Steel Copper T,> T
n electric generator at a power plant produces energy by passing superheated steam from a high temperature container (reservoir), through a pipe connected to a series of fans, and then into a low temperature reservoir. As the steam passes across the blades of the fans some of the heat energy of the steam is transformed into mechanical energy, which turns the fans which in turn are connected to a generator, which in turn converts the mechanical energy into electrical energy. If the high temperature steam has a temperature of 412.1 K and the low temperature reservoir has a temperature of 105.4 K, what is the Carnot efficiency of this process?
A steel pipe with heat transfer coefficient of 42 W/mK contains flowing water. The outer diameter of the pipe is 90 mm and the wall thickness is 3mm. Calculate: i. The heat loss by convection and conduction per meter length of un-insulated pipe when the water temperature is 14°C, the outside air temperature is -10°C, the water side heat transfer coefficient is 30 KW/m^2K and the outside heat transfer coefficient is 20 KW/m^2K. ii. Calculate the corresponding heat loss when the pipe is lagged with insulation having an outer diameter of 200 mm, and thermal conductivity of K = 0.05 W/mK
Find the heat flow rate through the composite wall as shown in the following figure. Assume one dimensional flow and take k 1 = 150 W/m degree, k 2 = 30 W/m degree, k 3 = 65 W/m degree, k 4 = 50 W/m degree. AB = 3 cm, BC = 8 cm and CD = 5 cm. The distance between middle horizontal line from the top is 3 cm and from the bottom is 7 cm.