A STATCOM is built next to an existing LCC to compensate its power factor back to unity. Calculate the maximum reactive power this STATCOM would have to generate in the worst-case scenario, for the parameters below. AC line voltage at the connected 3-phase bus: 400 kV RMS, transformer ratio: 0.65, Rated DC current: 2.0 kA, minimal firing angle: 9 degrees.

A STATCOM is built next to an existing LCC to compensate its power factor back to unity. Calculate the maximum reactive power this STATCOM would have to generate in the worst-case scenario, for the parameters below. AC line voltage at the connected 3-phase bus: 400 kV RMS, transformer ratio: 0.65, Rated DC current: 2.0 kA, minimal firing angle: 9 degrees.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
13. The transformer in a large welder provides single-phase ac output at 30 V, 50 Hz. An SCR bridge is used to control the welder. A large inductor helps to maintain a welding arc. a. What phase delay angle should be used to set an initial voltage of 25 Vac? b. The phase angle drops back once the arc has formed. What phase delay angle is needed for 8 Vdc output?
None
I need the answer quickly
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
Q8
In a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic i.e, fast system response? How about when duty cycle changes slowly i.e, slow system response?
Q1// What is the purpose of conducting CD experiments (o.c) and (s.c) on asingle phase transformer?
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.