A star-connected three-phase load absorb 3000 W with power factor 0.433 lagging has a resistance series with an inductance in each branch. It is connected to the 400Vrms (line voltage), 4-wire, 50 Hz, 3-phase supply with the phase sequence is ABC and phase-A as reference has angle 10°. a. Sketch the circuit diagram of the system.

A star-connected three-phase load absorb 3000 W with power factor 0.433 lagging has a resistance series with an inductance in each branch. It is connected to the 400Vrms (line voltage), 4-wire, 50 Hz, 3-phase supply with the phase sequence is ABC and phase-A as reference has angle 10°. a. Sketch the circuit diagram of the system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.52P: A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Derive the relationship between in case of star and delta connected load between: a). Phase voltage and line voltage b). Phase current and line current
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Differentiate Wye and Delta Connection in Three Phase System and Relate it with Computer Engineering
Transkrmers phase with each bank with - adjuste 35. Three single-phase transformers, cach of 100 kVA rating, are conected in a closed-delta arrangement. If one of them is taken out, it would be possible to load the bank in such a manner that cach one is loaded to the extent of: A 86.6 kVA C. 57.7KVA B. 66.7 kVA D. 33.33 kVA when load is at unity power factor. 36. Average power factor at which V-V bank separate is A 86.6% C. 66.67% В. 73.3% D. None of these 37. Scott connections are used for: A. single-phase to three-phase transformation C. three-phase to two-phase transformation B. three-phase to single-phase transformation (D Any of the above 38. The current in low voltage winding of a 25 kVA, 6600/400 V, 50 Hz, 3-phase Y-A transformer, at full load is: A 36 A Č. 65,32 A B. 20.78 A D. 40.2 A 39. The current in high voltage winding of a 20 kVA, 2200/220 V, 50 Hz, 3-phase A-A transformer, at full load is: (A. 3.03 A C. jo.5 A B. 5.25 A D. None of above 40. The current in low voltage…
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
Discuss Fully the various methods available for transforming 3-phase voltages to higher or lower 3-phase voltages. Highlight the advantages and disadvantages of each. Include the connection diagrams.
Subject - Design electrical circuits for single phase AC networks Question - Analyse the methods that improve the power factor of a electrical circuit.
Design a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with ACB sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”.
28 k